+- Woodnet Forums (https://forums.woodnet.net)
+-- Thread: Push Block Grip Pad??????????????????? (/showthread.php?tid=7193189)
Push Block Grip Pad??????????????????? - kegler01 - 01-14-2016
I am making a push block type of device and am getting towards the end of the project. I have it all figured out except what to use for a grippy rubber bottom that can be adhered to wood. My original thoughts were to use a mousepad and I still like the idea. My question is does a mousepad create enough friction with wood to use as a bottom on a push block. My biggest concern is longevity of the mousepads and do they work when dust is present.
Re: Push Block Grip Pad??????????????????? - danw - 01-14-2016
Does your push block have a heel? If so it doesn't matter much what you use. I have always used sand paper glued to the bottom. Sorry but I can't speak to the mousepad.
Re: Push Block Grip Pad??????????????????? - Paul-in-Plymouth - 01-14-2016
LV offers high-friction sheet material with PSA backing that works well for this sort of thing.
http://www.leevalley.com/US/wood/page.aspx?p=67844&cat=1,43456,43465
Re: Push Block Grip Pad??????????????????? - Phil S. - 01-14-2016
I've made push blocks with a mouse pad glued on the bottom. There are a lot of different types of mouse pads and obviously some will work well while others won't work worth a ****. Thin ones work better, last longer. The pad eventually comes unstuck, but a bit of contact cement fixes it. Dust will make them less sticky. You can wipe them off with a damp cloth and pretty much be back in business. Other non-skid type materials would work as well as long as the surface to your project is tacky and you can glue the opposing surface to your push block, but you can find mouse pads for free. But I have to agree with DanW that my preference is for a push block with a "heel" so you have a mechanical stop rather than just friction working for you. Friction alone will not be as positive or dependable.
Re: Push Block Grip Pad??????????????????? - Big Dave - 01-14-2016
Paul-in-Plymouth said:
LV offers high-friction sheet material with PSA backing that works well for this sort of thing.
http://www.leevalley.com/US/wood/page.aspx?p=67844&cat=1,43456,43465
This is what I've used with pretty good results...
Dave
Re: Push Block Grip Pad??????????????????? - DaveParkis - 01-14-2016
Go to Walmart and get some shelf liner. Its just like what LV sells except it won't prevent rust. I bought a couple rolls a few years ago and use it for free hand routing, too.
Re: Push Block Grip Pad??????????????????? - rwe2156 - 01-14-2016
Don't expect it to grip that well.
I like a strip of 80 grit sandpaper myself.
Even with that, often times I need something with a heel especially on the jointer.
Re: Push Block Grip Pad??????????????????? - DFJarvie - 01-14-2016
LV stuff works fine. I'm due to redo my push blocks.
Re: Push Block Grip Pad??????????????????? - DaveParkis - 01-14-2016
rwe2156 said:
Don't expect it to grip that well.
I like a strip of 80 grit sandpaper myself.
Even with that, often times I need something with a heel especially on the jointer.
It seems to work pretty well for my jointer. Of course, I still put heels on the push blocks.
Re: Push Block Grip Pad??????????????????? - kludge - 01-14-2016
DaveParkis said:
[blockquote]rwe2156 said:
Don't expect it to grip that well.
I like a strip of 80 grit sandpaper myself.
Even with that, often times I need something with a heel especially on the jointer.
It seems to work pretty well for my jointer. Of course, I still put heels on the push blocks.
[/blockquote]
Someone a while back said that skate board grip tape was a good substitute for sand paper. I've not tried, but it seems like a good idea at the time...