Users browsing this forum: 44 Guest(s)
Rules of Conduct |
The opinions expressed herein are those of the users and do not reflect the views of Active Interest Media. By using this site, you agree to our Terms of Service. |
Woodworking
|
|||||
Thread / Author [asc] | Replies | Views | Last Post | ||
How would you "divide" these feet?
09-06-2023, 07:37 PM
|
7 | 846 |
09-12-2023, 09:35 AM Last Post: jteneyck |
||
Shop paint type?
07-10-2017, 01:10 PM
|
4 | 2,922 |
07-10-2017, 05:04 PM Last Post: Steve N |
||
Knock-down executive desk design--castle joints?
01-02-2023, 01:41 PM
|
2 | 748 |
01-02-2023, 03:49 PM Last Post: ®smpr_fi_mac® |
||
Ambrosia maple writing desk done
11-18-2023, 01:24 PM
|
9 | 1,089 |
11-27-2023, 12:08 PM Last Post: AHill |
||
DIY Panel Clamps!
(Pages:
1
2
3
)
05-14-2018, 02:48 PM
|
27 | 18,312 |
05-18-2018, 01:19 PM Last Post: BloomingtonMike |
||
Burl veneer source?
11-16-2018, 05:46 PM
|
5 | 2,638 |
11-18-2018, 04:39 PM Last Post: handi |
||
Suppliers for plate glass?
10-21-2017, 06:07 PM
|
9 | 5,520 |
10-23-2017, 01:16 PM Last Post: ®smpr_fi_mac® |
||
How would you mount this escutcheon?
11-16-2018, 09:25 PM
|
7 | 3,296 |
11-19-2018, 11:23 AM Last Post: ®smpr_fi_mac® |
||
What size piano hinge?
(Pages:
1
2
)
12-30-2017, 02:49 PM
|
10 | 9,039 |
12-31-2017, 03:58 PM Last Post: Rick Barton |
||
Math/angle help?
(Pages:
1
2
)
10-17-2019, 07:47 PM
|
14 | 6,357 |
10-27-2019, 09:55 AM Last Post: tablesawtom |
||
How would you lay out these curves?
(Pages:
1
2
)
09-11-2023, 05:58 PM
|
15 | 1,786 |
09-19-2023, 10:47 AM Last Post: nodima |
||
Small diameter furniture leveling feet?
08-17-2022, 08:38 PM
|
4 | 1,177 |
08-18-2022, 06:48 PM Last Post: ®smpr_fi_mac® |
||
Heavy duty dining table leveling feet?
04-23-2022, 11:38 AM
|
3 | 2,052 |
04-24-2022, 11:03 AM Last Post: ®smpr_fi_mac® |
||
Kitchen table design help? Also chairs?
02-22-2016, 08:59 PM
|
4 | 5,217 |
03-08-2016, 12:55 PM Last Post: ®smpr_fi_mac® |
||
How many figure-8 clips for this table?
05-10-2022, 09:04 AM
|
4 | 1,524 |
05-11-2022, 08:48 AM Last Post: rwe2156 |
||
Shop door question
07-11-2017, 05:39 PM
|
3 | 2,755 |
07-12-2017, 08:34 AM Last Post: fredhargis |
||
Have you built a spline jig yet?
04-18-2019, 08:08 AM
|
8 | 4,638 |
04-21-2019, 09:13 AM Last Post: handi |
||
What size hole to drill?
05-15-2018, 05:36 PM
|
5 | 4,370 |
05-19-2018, 07:32 AM Last Post: ®smpr_fi_mac® |
||
Question on designing built in cabinets
06-15-2015, 10:50 AM
|
9 | 6,232 |
09-18-2015, 10:47 AM Last Post: Bill Lyman |
||
Brown paper supplier?
(Pages:
1
2
)
04-18-2019, 01:18 PM
|
13 | 6,461 |
04-20-2019, 04:06 PM Last Post: Big Dave |
||
- New Posts
- Hot Thread (New)
- Hot Thread (No New)
- No New Posts
- Contains Posts by You