Users browsing this forum: 130 Guest(s)
Rules of Conduct |
The opinions expressed herein are those of the users and do not reflect the views of Active Interest Media. By using this site, you agree to our Terms of Service. |
Woodworking
|
|||||
Thread / Author [desc] | Replies | Views | Last Post | ||
would 41" be too wide for a "toe-kick drawer"
01-25-2022, 04:41 PM
|
9 | 1,958 |
01-27-2022, 02:31 PM Last Post: RichK |
||
is 3/8" too thin for kitchen drawer side? borderline?
(Pages:
1
2
)
03-26-2022, 01:58 PM
|
17 | 3,632 |
03-31-2022, 05:23 AM Last Post: kurt18947 |
||
upholstered headboard
08-15-2015, 08:26 AM
|
2 | 2,740 |
08-15-2015, 10:34 PM Last Post: MKepke |
||
to use breadboard ends or not??
(Pages:
1
2
)
11-27-2017, 10:39 AM
|
19 | 9,468 |
11-29-2017, 09:26 PM Last Post: WoodworkerTom |
||
This is brilliant
(Pages:
1
2
)
08-09-2016, 07:30 PM
|
12 | 5,995 |
08-10-2016, 04:33 PM Last Post: Steve N |
||
frameless cabinets -how thick for backs?
(Pages:
1
2
)
12-30-2021, 09:50 AM
|
15 | 3,374 |
01-06-2022, 08:53 AM Last Post: Cooler |
||
how much offset for tapered sliding dovetail?
12-27-2017, 10:59 AM
|
8 | 6,841 |
12-29-2017, 04:30 PM Last Post: mound |
||
pre-finished maple plywood, two colors
03-29-2022, 02:38 PM
|
7 | 1,253 |
03-30-2022, 09:01 AM Last Post: rwe2156 |
||
wood counter top with herringbone corner?
(Pages:
1
2
3
)
09-08-2020, 08:00 AM
|
23 | 7,498 |
09-11-2020, 09:35 PM Last Post: Bob10 |
||
question on using MDO
11-06-2016, 09:17 AM
|
6 | 6,990 |
11-07-2016, 02:54 AM Last Post: Lynden |
||
Wood ID help?
08-25-2020, 07:27 AM
|
5 | 1,666 |
08-26-2020, 07:08 PM Last Post: Scoony |
||
where did I go wrong - repeatability..
08-04-2016, 11:20 AM
|
9 | 5,060 |
08-05-2016, 06:59 AM Last Post: Steve N |
||
finish for edge of pre-finished maple ply?
09-03-2021, 10:07 AM
|
4 | 1,570 |
09-04-2021, 03:56 PM Last Post: zaret |
||
desk build, surprising wood movement/crack.. or something else?
(Pages:
1
2
3
)
10-08-2020, 08:23 AM
|
22 | 5,449 |
10-12-2020, 08:43 AM Last Post: mound |
||
under drawer dovetail guide - tips tricks?
(Pages:
1
2
)
12-26-2019, 06:21 PM
|
14 | 6,017 |
12-28-2019, 12:08 PM Last Post: DaveR1 |
||
breadboard end technique
02-25-2019, 11:09 AM
|
7 | 3,854 |
02-26-2019, 10:08 AM Last Post: rwe2156 |
||
sketchup help - re-close curved face?
01-15-2018, 10:43 AM
|
3 | 2,280 |
01-15-2018, 11:49 AM Last Post: DaveR1 |
||
question on veneering, pulling a panel flat if slightly bowed
(Pages:
1
2
)
02-13-2019, 02:17 PM
|
13 | 6,284 |
02-14-2019, 10:44 AM Last Post: Stwood_ |
||
*update* tips for consistent repeatable double bridle joint
(Pages:
1
2
)
03-31-2020, 04:49 PM
|
10 | 5,834 |
04-01-2020, 06:12 PM Last Post: barryvabeach |
||
Ash tree coming down, worth milling?
(Pages:
1
2
)
07-29-2020, 05:46 PM
|
15 | 11,127 |
08-12-2020, 09:40 AM Last Post: Arlin Eastman |
||
- New Posts
- Hot Thread (New)
- Hot Thread (No New)
- No New Posts
- Contains Posts by You