+- Woodnet Forums (https://forums.woodnet.net)
+-- Thread: Just another Box Project? (/showthread.php?tid=7377290)
Pages:
1
2
Just another Box Project? - bandit571 - 11-19-2024
Hey, gotta use up the leftovers, some how.....Maybe resaw a stack down to 1/2" thick...glue a few into panels?
IF anyone wants to follow along.....will start this after all the errands for today have been run....
Stay tuned...
RE: Just another Box Project? - professore - 11-20-2024
I'll be following.
Frank S in IA
RE: Just another Box Project? - MarkSingleton - 11-20-2024
Yup. Me too!!
RE: Just another Box Project? - stav - 11-20-2024
Did you pick up a new tool you need to share that needs a box? Should be interesting.
RE: Just another Box Project? - bandit571 - 11-20-2024
Resaws were done on the tablesaw...stuff that wasn't usable, was tossed. Trying to keep the better looking stuff...like these...
[attachment=53053]
Goal was to find enough pieces that I could match up..
[attachment=53054]
Some better than others..
[attachment=53055]
And try for 4 panels glued up....
[attachment=53056]
#4 was sitting over on the bench...Panels are 1/2" thick Ash.
Let these sit a day or 2...Middle one of those 3 was to be the "Lid"....Turned out, that I needed a 3 strip glued to it..
[attachment=53057]
Still have not removed THOSE clamps, yet...will wait until I start Lid Work...
To help things out, panels were rip to 6" wide...as that is all the wider the vise will open..
[attachment=53058]
This is Panel #4, the "Back" of the case....needed planed flat and smooth..
[attachment=53059]
A #3 seemed to work just fine....other planes in use?
[attachment=53060]
A #4-1/2 and a #6c.mainly to joint an edge or 2 before a glue up...
There was one board that wasn't a glue-up, though..
[attachment=53061]
Just needed smoothed down a bit.....Case has 2 drawers, and an upper compartment.....and this is the front of that compartment...
[attachment=53062]
Stay tuned...corner joints will be through dovetails..LOTS of Through Dovetails...
RE: Just another Box Project? - bandit571 - 11-21-2024
Through Dovetails for the corners...
[attachment=53063]
Lay out tools...and..
[attachment=53064]
Lay out lines...
[attachment=53065]
Saw the lines...doing pins first, of course...
[attachment=53066]
Start with the face that will show, chop half way down....leave a little "porch" for support...flip panel over..
[attachment=53067]
Chop out the waste...use these pins to mark out the tails...Bandsaw to cut strictly on the waste side of the lines, leaving the line, in fact...remove the waste, and try a dry fit..
[attachment=53068]
When I NEED a hammer to drive thing "home", I think that will be tight enough...repeat for the second full height (6") corner...
[attachment=53069]
Yes, these sides are a whopping 6" tall...however...across the front?
[attachment=53070]
This sits above 2 drawers..
[attachment=53071]
And will be the front of the Compartment...
Clamps, glue and cauls..
[attachment=53072]
Let this sit a day..or 2...
Stay tuned..Have slips and a base to do next.....then work on 2 drawers
RE: Just another Box Project? - BpB123 - 11-22-2024
Looking good!
Thanks for sharing!!
RE: Just another Box Project? - bandit571 - 11-24-2024
Hey,, is my slip showing?
[attachment=53087]
These...are called "slips"...I used 4 to install a floor inside this box...mitered corners means...
[attachment=53088]
Rotating the saw to 45 degree detent...and start here..
[attachment=53089]
As this one is as low as I can go...Was going to use a square to draw a couple lines for the other 3...wound up setting a small combo square for depth...glued in the back slip...then glued in the end slips..
[attachment=53090]
Just glue..no metal was used...
Once the clamps came off the next day..
[attachment=53091]
A 1/4" plywood panel was cut to a loose fit...then some weight was added as the panel was glued down...
[attachment=53092]
And let this sit a day...
Stay tuned...
RE: Just another Box Project? - bandit571 - 11-24-2024
A Base by Bugtussle?
There USED to be a 1 x 8 x 6' plank in the shop...mainly Ash Sapwood...Used to be?
[attachment=53093]
Went all through that plank..cut out the "good" stuff...and this mess is what was left...will go to the fire pit...soon...
[attachment=53094]
Yep, this is what is left....I also resawed the worst face...until the slat were 5/8" thick...I jointed the edges a bit for a glue up..
[attachment=53095]
Let this sit a day....then..
[attachment=53096]
Planed the panels faces ( both of them) as flat as a Stanley #3, Type 15 could get it...then...to keep it reasonably flat..
[attachment=53097]
It had already started to curl a bit, so..it got clamped to the bottom of the case....
Then, I could try to get the drawer front(s) sized...
[attachment=53098]
Turned out, that the fronts plus the divider were a tad too FAT....we have ways..
[attachment=53099]
Ripped about half the thickness of the tablesaw blade off one edge of each front....then the plane to joint the edges...as I wanted both drawers to match each other...
Stay tuned..Drawer building 101 will be next episode..
RE: Just another Box Project? - bandit571 - 11-27-2024
Drawer boxes....use through dovetails just like the rest of the box...except for the "Front" which also gets a rebate to "house" the bottom of the drawer..
[attachment=53105]
With the sides and back ripped to match the depth of the drawer.
[attachment=53106]
Front has 3 tails...
So, once the pins are done, I use them to trace out the tails....then cut on the waste side of the lines...on the bandsaw..because..
[attachment=53107]
I can SEE the lines to be cut...and on these small critters..I can actually cut the waste out...
Backs get one less tail...
All 4 corners are done, I also cut a 1/4" plywood panel to size...then do a glue up of all 5 parts....
[attachment=53108]
Then do the same for the other drawer...
[attachment=53109]
And, since the corners of the plywood are square, I use it to make sure the rest of the drawer is square...
Once the first drawer is out of the clamps and cleaned up...
[attachment=53110]
I have a pair of wood knobs, as Drawer Pulls....but, they came with a hole to add a dowel in, to act as a "tenon"...glue in the dowel, cut it to length...drill a hole centered in the drawer front...and glue it into place..
[attachment=53111]
And wait while the second drawer cures in the clamps....
Stay tuned...have to install something for the "upper" drawer to slide on...Next time...