+- Woodnet Forums (https://forums.woodnet.net)
+-- Thread: Daily Bench Shot (/showthread.php?tid=7336585)
Pages:
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
RE: Daily Bench Shot - mongo - 02-17-2019
(02-17-2019, 07:09 AM)Belle City Woodworking Wrote: Great job Mongo!
Thank you
RE: Daily Bench Shot - Redman - 02-17-2019
(02-17-2019, 07:51 AM)mongo Wrote: Thanks! A "Dark walnut" stain and then lacquer.
RE: Daily Bench Shot - Stwood_ - 02-17-2019
[attachment=16584]
[attachment=16583]
RE: Daily Bench Shot - fishhh4 - 02-17-2019
Uhhh ... ya missed a spot.
RE: Daily Bench Shot - Redman - 02-17-2019
(02-17-2019, 01:34 PM)fishhh4 Wrote: Uhhh ... ya missed a spot.
Helper has it under control. Check the white pad. Helper standing there supervising.
RE: Daily Bench Shot - Stwood_ - 02-17-2019
........................
RE: Daily Bench Shot - Peter Tremblay - 02-17-2019
I'm shaping the totes of the infills.
Here you can see the layout lines.
[attachment=16605]
The first tote I carved with a rotary tool and a carbide carving burr. It went alright but shaping like this means a lot of stock removal and it is much harder trying to carve end grain so it took a while.
[attachment=16606]
Then I decided to go back to the tried and true method of rasps. This is much quicker, much more uniform, much easier, and no fine dust.
[attachment=16607]
You can see that I've roughed out the back of the tote all the way to the layout lines. Now I need to rough out the inside of the tote.
Bye the way after I'm done making some infills I will never work with lignum vitae again...maybe This stuff is more wear resistant than steel. A file on lignum vitae end grain removes material slower than on steel.
I haven't begun to sand any of the totes yet. So after rough carving I'll probably start with some 80 grit and then go to 2000.
RE: Daily Bench Shot - Redman - 02-18-2019
..........................
RE: Daily Bench Shot - mongo - 02-18-2019
(02-17-2019, 11:38 PM)Peter Tremblay Wrote: I
Bye the way after I'm done making some infills I will never work with lignum vitae again...maybe This stuff is more wear resistant than steel. A file on lignum vitae end grain removes material slower than on steel.
I haven't begun to sand any of the totes yet. So after rough carving I'll probably start with some 80 grit and then go to 2000.
Peter beautiful work!
I used to work a lot with exotics. If you haven't tried yet I suspect you'll find that it scrapes for extremely well. Also you might want to try actually buffing the stuff on a buffing wheel after sanding ,with white compound, when you are done. It will look like Stone. Try it on a piece of scrap first to see if you like the look.
The stone look will fade a bit in time as the oils continue to leak out of the lignum.
RE: Daily Bench Shot - Belle City Woodworking - 02-18-2019
Well, we are starting to get the depth or warmness that I have been looking for. I think one or two more coats and this piece will be ready for delivery.
![[Image: 57210080515-41071416-72-FF-4-B64-9-CBD-A...-F3786.jpg]](https://i.postimg.cc/fysVK5QT/57210080515-41071416-72-FF-4-B64-9-CBD-AFA8292-F3786.jpg)
In case you didn't catch it in an earlier post, the finish is Minwax Antique Oil Finish, 3 coats with a light sanding between coats, after the final coat of antique oil finish was allowed to fully cure for a week, it was then top coated with (so far) 4 coats of Minwax Satin Poly with a light sanding between coats.
The folks I am building this table for did not want any defects repaired which made this just a little easier.
I have thoroughly enjoyed this thread!
John