+- Woodnet Forums (https://forums.woodnet.net)
+-- Thread: another build thread... (/showthread.php?tid=7335748)
RE: another build thread... - bandit571 - 01-21-2018
(01-21-2018, 09:12 AM)Rick Barton Wrote: So what was the book?
Brandon Sanderon Oath Bringer/ Book 3 of The Stormlight Archive........
9-1/2" tall...needs a shelf 7+" deep. My son has a lot of books about the same size
RE: another build thread... - Rick Barton - 01-21-2018
(01-21-2018, 12:25 PM)bandit571 Wrote: Brandon Sanderon Oath Bringer/ Book 3 of The Stormlight Archive........
9-1/2" tall...needs a shelf 7+" deep. My son has a lot of books about the same size
Ah, so you're making this for your boy, that's very cool.
RE: another build thread... - bandit571 - 01-21-2018
Got a bit of work done, today....wanted to S4S the two side pieces.....some of the edges didn't quite match each other...we have ways
[attachment=7475]
Stanley #70 SW Scraper plane
[attachment=7476]
Took the high spots right down.....there was a few places for a couple other planes to work on
[attachment=7477]
Like edges needed straightened. Stanley #6c, T-10 helped out, along with the Millers Falls #14.....goal was to get both sides to match..
[attachment=7478]
Well, that was the plan.
....had to trim the board on the bottom, to match the one on top....[attachment=7479]
Then S4S the second plank....I still had the locations for three shelves laid out....more on that, in the next exciting episode
Stay tuned
RE: another build thread... - bandit571 - 01-21-2018
Ok, this will involve the use of a corded tool...sorry about that, but
[attachment=7480]
I needed to cut a few sockets, for sliding dovetails.....so I can install the shelves, later...
Home made fence, set to guide the bit in the center of each location.
[attachment=7481]
Got one plank done, came time to do the other...had to set the fence a bit differently
[attachment=7482]
And pull the router towards me. No biggie. Once all the sockets were done, I set up a different type of fence
[attachment=7483]
So I can mill a "pin" on the end of each shelf...
[attachment=7484]
Decided this could wait until later...decided to get back to hand plane work
Coming up next episode....stay tuned
RE: another build thread... - Rick Barton - 01-21-2018
RE: another build thread... - bandit571 - 01-21-2018
Ok, back to hand tool stuff
Wanted to milled a rebate along the "back" edge of the sides....to house the 1/4" plywood back. Set up Old Reliable
[attachment=7485]
With a #17 cutter. Depth set so the plywood would be flush, and not show, and a lip was set up
[attachment=7486]
Something like this. I had a scrap of the plywood handy, to double check things..
[attachment=7487]
Going across those sockets didn't seem to bother anything....got both rebates milled
[attachment=7488]
Had to double check things, to make sure I was adding the rebate to the correct edge....didn't want one in front, and one in the back, plywood doesn't quite work that way.....Once I made sure, then I could mill the other rebate....made a lot of shavings on the floor...
[attachment=7489]
Almost wished I had turned that fan on...I was soaked. Might have done a wee bit too much, today?
Stay tuned, maybe tomorrow, I can add some shelves?
RE: another build thread... - Tynyyn - 01-21-2018
Nice continuation of work. Have you given consideration of videoing you journey? Nothing fancy, just a static GoPro set up in the corner of your shop and maybe some quick editing so we can get the gist of how you are doing things.
RE: another build thread... - bandit571 - 01-21-2018
(01-21-2018, 06:50 PM)Tynyyn Wrote: Nice continuation of work. Have you given consideration of videoing you journey? Nothing fancy, just a static GoPro set up in the corner of your shop and maybe some quick editing so we can get the gist of how you are doing things.
Don't have any video stuff to use.....don't know how to edit it, either.....someone else would have to do that....
RE: another build thread... - bandit571 - 01-22-2018
With the router still set up....made a few cuts..
[attachment=7523]
Just to check the set-up.....got bored, and finished the cuts..
[attachment=7524]
Got all the ends milled, so...out came the hammer
[attachment=7525]
And drove each shelf in, until flush with the front.....which left about 2" to add a filler to..
[attachment=7526]
Then I can add a back to the case. Need to add a top, and cleats to attach this to the bottom case. Some other day,,,I am plumb tuckered out.
Was no glue used, just a tight, press fit. May add a spot of glue, when I add the filler strips.
Stay tuned....
RE: another build thread... - bandit571 - 01-23-2018
Decided to try a bit of work, BEFORE Lunch.....hauled a board to the shop...squared one end, marked a spot 26" from that, and made a crosscut. Turn the leftover end for end, marked a 26" line again....there WAS a huge knot way out on this end....since it was beyond the 26" mark...no biggie..just lopped it off. Laid the two pieces side by side..
[attachment=7545]
Seems the edges will need a bit of work?
[attachment=7546]
We have ways....
[attachment=7547]
I took the time to mark the "show" sides...with a big "V"
[attachment=7548]
Took a while, but was finally able to spread a bead of glue, and add a few clamps
[attachment=7549]
And decided to let it sit a while...after all, it was Lunch time
Need to haul a couple more planks to the shop...AFTER Lunch....Face frame parts, and door parts are next.
Stay tuned....