+- Woodnet Forums (https://forums.woodnet.net)
+-- Thread: A Project for the Boss (/showthread.php?tid=7342235)
RE: A Project for the Boss - bandit571 - 10-05-2018
Well, the door came out of the clamps..was even in one piece
needed one edge jointed..[attachment=13542]
Top needed squared up
[attachment=13543]
Hinges installed..and find out where the knob is to go
[attachment=13544]
needed a shim under the door, and then installed it...shim so the door doesn't drag the bottom edge when you ope/close it
[attachment=13545]
Then, right after this, a hammer and chisel and go around trimming plugs until they were flush....Needed to move the entire case a bit...needed to get my fat...body into the shelf area..
[attachment=13546]
Still not all that much room...that trash can WAS empty, when this Project started, BTW
Had this all the way over, against the bandsaw...had one more task to do...
Stay tuned...
RE: A Project for the Boss - bandit571 - 10-05-2018
Ok, those HD 1 x 12s? Needed 4 pieces, 13-1/8" long....
[attachment=13548]
Three to make the shelves, the fourth to make a filler strip across the back...
[attachment=13549]
Even used a "work light". Top two shelves sit on 1 x 1 cleats....bottom is screwed down to the bottom frame. Door done, plugs trimmed...moved this huge case aside a bit..
[attachment=13551]
Decided to move it a bit more...both to get some room for sanding things, and...
[attachment=13552]
Get enough light to show off a bit. Needs the fireplace insert installed...once it gets out of the shop
[attachment=13553]
Will get to this the firepit...IF it will stop raining for a day...
Stay tuned...sanding, stain and Amber Shellac coming up later...
RE: A Project for the Boss - mound - 10-05-2018
RE: A Project for the Boss - Arlin Eastman - 10-06-2018
Steve
Not being mean but just do not understand why.
With all the gaps you had on this and other builds and you always squaring everything up just why is there gaps? It all should fit together prett tight correct?
RE: A Project for the Boss - bandit571 - 10-06-2018
Because things shift a bit when clamped up....
RE: A Project for the Boss - bandit571 - 10-07-2018
A coat of Amber Shellac has been applied, over that coat of Weathered Oak stain...will see how it dries..
RE: A Project for the Boss - bandit571 - 10-08-2018
Well, I thought that a couple bright steel turn knobs would match the rest of the hardware on the case...
[attachment=13578]
However...I was then informed by a self-appointed Furniture "Expert" ( aka TROLL) that the project now sucks, by my use of such "cheap" hardware....ruined the whole look...was even cussed at....on another site...
Hmmm...
Already had the first coat of Amber Shellac on, waiting for the smell to die down....Had a bit of 1 x 1 Walnut scrap......Bandsaw to chop off a chunk, then resaw it into a pair of blanks...made a design and sawed that out.....Added a washer behind each. Hole was to use the screws from the Cheap Latches...and they sit in counter-sunk holes..
[attachment=13580]
Can really say that these new latches are indeed "cheap". Whether they look cheap is not what I am interested in....let the sock-puppet Critics worry about it...the Boss likes them.
[attachment=13581]
Just turn them down...doesn't really matter which way....they work just as well, either way..
[attachment=13582]
Then gave the top of the case a second coat of shellac...and closed the shop...Maybe Tuesday, I can add a coat of gloss poly...and haul it out of the shop later this week...woodworking is 99.9% done. Once it is upstairs, I can add the plywood backs. And..install that fireplace insert.
RE: A Project for the Boss - mound - 10-09-2018
nicely done!
if the boss likes it, that's all that matters.
RE: A Project for the Boss - bandit571 - 10-09-2018
Will have to rub this out, tomorrow, but
[attachment=13593]
One coat of clear gloss varnish has been brushed on
Top needs the rub down the most....
[attachment=13594]
Old, CLEAN T-shirt to buff things out.
needs to be hauled upstairs, backs and the insert installed....and the entire mess placed in the Living Room.....and sit the TV and boxes on top.
IF anyone wants, I could post a picture, or two, of it when installed?
RE: A Project for the Boss - mound - 10-09-2018
(10-09-2018, 07:22 PM)bandit571 Wrote: anyone wants, I could post a picture, or two, of it when installed?
yes!