+- Woodnet Forums (https://forums.woodnet.net)
+-- Thread: Need advice on how to do something (/showthread.php?tid=7323041)
RE: Need advice on how to do something - Imakmst© - 09-22-2016
yes, I've done all to that frig it will allow
RE: Need advice on how to do something - JGrout - 09-22-2016
(09-22-2016, 08:05 AM)Imakmst© Wrote: It's a one piece floor to ceiling unit that can't come down
I need to take some off the rail leaving the stiles alone, like where the arrow is pointing.
you have another issue to deal with that you have not considered
the protrusion on the left will stop even the smallest router dead ~3" from the stile
If I were doing it I would make a fairly large surfaced straightedge to cover at least 6" of the upper opening and clamp it to the stiles ( if there is enough to clamp to, if not make backers to fit in the opening set in a small amount from the edges inside the opening then wedge it in on both sides) Then get a long (preferable spiral) trim bit to fit that 892 you have. On the right I would make a stop to fit the surface jig you make and on the left Well that is not going to be simple but with a larger router and bit opening hole you can see where to stop at. A bit of chisel work and you should be good to go...
running a router horizontal only take a bit more arm strength It is not like you are removing a lot of stock. Oh and router direction matters so think the cuts through before you start
JMO
![[Image: Capture_1_zpsg5ra3rhv.jpg]](http://i158.photobucket.com/albums/t99/imakmst/Capture_1_zpsg5ra3rhv.jpg)
RE: Need advice on how to do something - Imakmst© - 09-22-2016
all good advice but that is a stock photo I found to explain the "what I got to cut". My cabinet face frame is such that I can get a clamping straight edge on it just as if I was using the clamping edge on a pc of plywood, so not issues with that. (both sides look like the right edge in that photo)
RE: Need advice on how to do something - R Clark - 09-22-2016
I did this task last year for the top opening on our refrigerator cabinet. Our particular situation was that we put in new flooring that decreased the effective height of the opening.
I used the jig saw to cut most of it out then cleaned up the edge with a trim router and straight edge. Use a couple of quik-grip clamps to hold the straight edge in place. Watch the grain direction and you'll be fine.
RE: Need advice on how to do something - JGrout - 09-22-2016
I would still proceed as I suggested it just makes the project easier if you can install two stops.
Joe
RE: Need advice on how to do something - Stwood_ - 09-22-2016
Jigsaw, rasp to clean up then a sanding block.
Tape off the front of the rail so the jigsaw doesn't scar up your finish.
RE: Need advice on how to do something - sniper - 09-22-2016
(09-22-2016, 12:01 PM)WxMan Wrote: I used the jig saw to cut most of it out then cleaned up the edge with a trim router and straight edge. Use a couple of quik-grip clamps to hold the straight edge in place. Watch the grain direction and you'll be fine.IMHO, this is the best solution.
(09-22-2016, 01:59 PM)Stwood_ Wrote: Jigsaw, rasp to clean up then a sanding block.
Tape off the front of the rail so the jigsaw doesn't scar up your finish.
Good idea with the tape.
RE: Need advice on how to do something - joe1086 - 09-22-2016
Make sure your clamps are really secure. I've had Qwik grip clamps move/slip on me. You will be suspending a router six feet off the ground and and pushing it horizontally against the straightedge. Bad mojo if you are routing on finished cabinets and the guide moves.
Might be worthwhile to spend an half an hour making a jig with zero clearance to cradle the router. Clamp the jig to the cabinet.
I was going to compliment you on the nice looking cabinets, but never mind...
RE: Need advice on how to do something - Steve N - 09-22-2016
Bosch has some jigsaw blades they call "fine cut", that said their idea of fine cut, and mine differs. I'd go router. You could clamp straight boards across it to enable you to run your full size router on it. Your problem routing is you can't get that round trim bit to fit tight to the corners, so at some point you will need to use a chisel, or the jig saw. This brings the idea to just use a circular saw to cut the stretcher out completely, and replace it with a smaller model. Obviously you would need to stain/dye it to match. It looks like it is just hiding the edge of the plywood/particle board that is the shelf above the fridge.
RE: Need advice on how to do something - Stwood_ - 09-22-2016
Probably risky skill sawing the rail completely out, due to possible metal. Pocket screws perhaps, or brads.