+- Woodnet Forums (https://forums.woodnet.net)
+-- Thread: Nail puller. (/showthread.php?tid=7327415)
RE: Nail puller. - A Squared - 01-29-2017
(01-28-2017, 07:35 PM)daddo Wrote: I found this; http://www.homedepot.com/p/Crescent-19-in-Forged-Alloy-Nail-Puller-56/203984930 but I hate spending the money for one job.
I've used one of those a fair amount. I've also pulled some deformed shank underlayment nails ... my gut feeling is that you're gonna be disappointed with the results.
RE: Nail puller. - EricU - 01-29-2017
I have one of those slide hammer nail outeners. I used one to remove siding that was going to be reused, and it was really good for that. It really depends on the nail and the surface it's on, flat surfaces are better. so it might work ok on this floor. OTOH, you don't want to save the floor and can beat the nails in further, so destructive removal might be called for. I get mine out now when I'm going to reuse the wood, otherwise it can be annoying to use.
Kinda surprised those things still cost $40, I think that's what I paid for mine 20 years ago.
RE: Nail puller. - K. L. McReynolds - 01-29-2017
I helped a friend remodel a rental that had full thickness 2" by 4" white oak studs/ceiling joists and had lath and plaster walls/ceiling.
Quickly found we could not pull the nails and also could not hammer them flush. Had to use a 4" angle grinder to flush cut every stinking nail!
I have one of those slide hammer pullers---probably older than I am and still good. Never pulled even a half of one of those nails.
Flat bars---- 
Crowbars----
Cut----
RE: Nail puller. - chips ahoy - 01-29-2017
cut the nails off with a recip. saw and a metal cutting blade.
Mel
RE: Nail puller. - Stwood_ - 01-29-2017
You didn't say the sq footage of the kitchen, but taking that out in crumbled pieces is a huge task.
Why not cut out the bad spots and replace those, then retile
RE: Nail puller. - JGrout - 01-29-2017
(01-28-2017, 11:56 PM)daddo Wrote: I think something like that would work- would like it to be more sturdy if possible. I'm going down tomorrow and take a look. Thanks.
You would be surprised at how sturdy they are I have two shorter ones ( from Vaughn) and one is well over 35 yrs old and still working just fine. I have pulled nails in floors, walls trim, shingles and even used it extensively when I tore down a house
they are made to be beat on and hold up fine
Joe
RE: Nail puller. - Kreuzie - 01-29-2017
How about a drill-held hole saw (NOT a Forstner!) large enough to surround the nail and marked for a 7/8" depth of cut?
This would create "plugs" around the offending nails. You could then remove the particle board and deal with the nails as you see fit. Note: Buy several spare hole saws!
RE: Nail puller. - tomsteve - 01-29-2017
(01-28-2017, 11:56 PM)daddo Wrote: I can hammer the nails down if the heads come off. I pull the ones where the heads stay on.
The old linoleum from the 50's is still stuck to the wood- will be covering it.
in that case, how about renting a hammer drill with a chisel head? i had to remove parquet flooring nailed into old oak flooring once. sharpened up the chisel a bit and it made quick work of removal of the parquet.
RE: Nail puller. - daddo - 01-29-2017
I went with this one; http://www.homedepot.com/p/Estwing-10-in-Pro-Claw-Nail-Puller-PC250G/202033611
The pointed end penetrates and the nail head pops up fairly easily. I did have to modify the end some with the belt grinder- the end wasn't ground sharp enough. After the mod, it went fast!
Well worth it's weight.
RE: Nail puller. - museumguy - 01-29-2017
That's the one I have and love it. Hope all goes well.