+- Woodnet Forums (https://forums.woodnet.net)
+-- Thread: Cherry scraps, Project start up (/showthread.php?tid=7332982)
RE: Cherry scraps, Project start up - bandit571 - 09-09-2017
Clamps came off this morning
[attachment=4370]
Had to plane the edges of a Poplar panel...
[attachment=4371]
Was a tad too wide...we have ways...
[attachment=4372]
Stanley #4 was taking too thin of a shaving...took awhile...
[attachment=4373]
Also needed to use the plane on the end grain, to correct a wavy edge....
Finally got the bottom to fit down on the cleats I had glued on last night..
[attachment=4374]
Height looks about right.
Went to a friend's place, today. Traded a couple items for a stick of Black Walnut..1 x 4 x 7'
Will use it to build the lid with.....stay tuned
RE: Cherry scraps, Project start up - bandit571 - 09-09-2017
Camera battery is charged up....
[attachment=4390]
Mitre box saw to cut three pieces, jointed the edges, and clamped up into a blank. Will be a raised panel for the lid....
[attachment=4391]
This was ripped down the center, then clamped into the vise..
[attachment=4392]
Edges were jointed til they matched.
[attachment=4393]
These two were sawn down to make a pair of short rails, to go with the Long rails already done. made sure the edges were smooth..
[attachment=4394]
Letting the panel sit overnight. Maybe tomorrow, I can turn it into a raised panel. Need to drag the Stanley 45 back out, to plough grooves in the rails, to house the raised panel.
Had run out of Cherry, so walnut will just have to do.
....stay tuned...
RE: Cherry scraps, Project start up - bandit571 - 09-10-2017
Panel is out of the clamps, and planed flat..
[attachment=4408]
Bevels were made on the end grain first..
[attachment=4409]
Then the long grain was beveled, until a nice sharp corner appeared...
[attachment=4410]
Adjusted the jig, to allow the Stanley 45 to make a groove to house the raised panel in
[attachment=4411]
Then made a few tenons. Fought with a bunch of clamps and cauls...
too many parts, not enough hands. [attachment=4412]
Each corner has a pair of cauls, to keep the corners flat. It also keeps the clamps from dinging the surface.
Will let this mess sit up overnight. Will try to find some hinges tomorrow.....
MIGHT try to cobble a tray to sit inside the box? Ends of the lid are about flush with the ends on the box, may add a curve to the "front" edge of the lid...for a finger rest underneath the lid?
Nothing has been written down on paper, in the way of a "Plan"..has all been laid out inside my head...."Single Brain Cell Sketch Up" seems to do good work?
RE: Cherry scraps, Project start up - bandit571 - 09-11-2017
Lid id out of the clamps......trimmed things a bit..
[attachment=4419]
Was a bit too wide....trimmed a bit off the front and back. Left a tab out front for a finger rest, to lift the lid with...
Needs a lot of work yet. I did manage to buy some brass hinges today..
Monday is usually when the shop is closed.....maybe tomorrow, I can get a bit of work done?
[attachment=4420]
Stay tuned..
RE: Cherry scraps, Project start up - bandit571 - 09-11-2017
Figured I could at least try a coat of amber shellac...
[attachment=4423]
No hinges installed..yet..
[attachment=4424]
End view..
[attachment=4425]
Missed a couple spots...
[attachment=4426]
And that lid....will see about getting this things done....tomorrow?
Stay tuned
RE: Cherry scraps, Project start up - hbmcc - 09-11-2017
Looking nice! Have always liked walnut. Those rails sized differently from the stiles in the lid would drive me nuts, however.
RE: Cherry scraps, Project start up - JimReed@Tallahassee - 09-12-2017
Outstanding work. Great project.
RE: Cherry scraps, Project start up - bandit571 - 09-12-2017
Found a gouge...
[attachment=4453]
Tried my hand at a bit of carving..
[attachment=4454]
Got a couple hinges installed...
[attachment=4455]
Tried to make a couple trays.....cancelled that
they weren't working out the way I wanted them to Closed the lid..
[attachment=4456]
And added a coat of Clear Gloss Poly on top of two coats of amber shellac..
[attachment=4457]
Now, IF anyone wants to see a few more pictures..
Let me know....out of picture space in this post...Not too bad a little chest?
RE: Cherry scraps, Project start up - bandit571 - 09-14-2017
Sooo, this project is completed..
[attachment=4479]
Which means I need to clear off the bench,and decide what to build next
Have a panel, someone else had made..
[attachment=4480]
Supposed to be Maple. Then there is a stack of these boards
[attachment=4481]
Most are under 2' long. Lots of 1 x 8 and 1 x 6s just cut-offs
[attachment=4482]
This one is 5/4....had a split that finally cracked all the way through.....may rip the rest into stiles?
[attachment=4483]
Then this "square" panel....almost screams "Drawer front" ?
Will take a few days "off" to recharge the brain cells.....and see what I can cobble up next.
Stay tuned...
RE: Cherry scraps, Project start up - hbmcc - 09-14-2017
Your box came out very nice. Thanks for sharing the build.
Have you a recipient/customer? Purpose? I couldn't find mention. The impression I get is it was purely free creation. Nice one, too.