need to build a large work table - Printable Version +- Woodnet Forums (https://forums.woodnet.net) +-- Thread: need to build a large work table (/showthread.php?tid=7334875) Pages:
1
2
|
RE: need to build a large work table - TomFromStLouis - 11-19-2017 That’s going to be big but torsion boxes can be relatively light weight. You don’t need 3/4” material for the skins. RE: need to build a large work table - Wipedout - 11-19-2017 (11-19-2017, 06:40 PM)tomsteve Wrote: 5 by 10'- id say frame the top like a section of wall. Oh probably not more than 100 pounds if that RE: need to build a large work table - Steve N - 11-19-2017 (11-19-2017, 08:54 PM)AgGEM Wrote: You said 5x10. Worried about weight... build 2 smaller ones of whatever material you decide and put them together on site. Either that or just assemble the torsion box onsite. Except when you glue or screw the sheathing down they are something you can disassemble easily. Assembly on some adjustable saw horses that you can level make for a flat, level construction. Of the two choices I think making a pre-fab torsion box to size would be easier than trying to marry 2 together. RE: need to build a large work table - tomsteve - 11-20-2017 (11-19-2017, 09:50 PM)Wipedout Wrote: Oh probably not more than 100 pounds if that if thats the case, i dont think ya need to go overboard, although that would be my first instinct,too. 1/2" ply top with a frame of 1 by 4( you could use 3/4" ply ripped to 3 1/2" or even 3" so the frame would remain stable)) spaced 16" or even 12" and the top glued and screwed would make a very sturdy top. frame wouldnt be too bad. either. with the other info, i think id build 2- 5 by 5's and used some form of hardware to lock them together- something like whats used for leafs in kitchen tables. RE: need to build a large work table - jteneyck - 11-20-2017 Section modulus is related to stiffness and that formula is bh^2 where b = width and h = height. So it's the height of the grid members that dominate the ultimate stiffness, not the thickness; think of hollow core doors that are made with corrugated cardboard. I'm not suggesting you use that, but you can use 1/2" plywood around 5 - 6" in width for the grid then skin it with 1/4" plywood and it will be very light but very stiff. Design the grid so that the legs fit up into it and bolt them to the grid on site by making relief holes in the bottom of the grid to do that. If you want even more stiffness, add a stretcher between the legs under the torsion box. Attach your Melamine work surface on site. John RE: need to build a large work table - packerguy® - 11-20-2017 (11-19-2017, 01:03 PM)Wipedout Wrote: I have a friend (and client) whose business got flooded during Harvey 38 inches of water in her store. Amazingly I recovered her data off her hard drives after they were submerged in nasty water for 3 days Uline's packing tables are real hard to beat. I have a 3'x5' table and I would be hardpressed to make it for what it cost (Around $250) Heavy steel base and I have the composite top (mdf core with outside skins of particleboard, with a heavy poly finish...1-1/2 thick) I think the largest they sell is 4'x8' If cost and strength is the main goal and nobody care what it looks like, id buy some 2x lumber and some mdf and sheet laminate and a gallon of paint and get it done. |