+- Woodnet Forums (https://forums.woodnet.net)
+-- Thread: Diminutive Dovetail chisels (/showthread.php?tid=7353852)
RE: Diminutive Dovetail chisels - Arlin Eastman - 03-26-2020
Very nice and well done on the handles!!!!
Is that the kind of chisels that they were talking about (Kerfing chisel)??
RE: Diminutive Dovetail chisels - jcredding - 03-26-2020
Those are simply stunning. I really want to buy them, but now is not the time (and if I repeat that enough, I might eventually convince myself).
And just saw on the blog they were sold - not sure who I need to thank, but they’re out there.
RE: Diminutive Dovetail chisels - Aram - 03-26-2020
Ron,
Those are gorgeous. Would you consider making a narrow one under 1/8" Say, 3/32" or thereabouts?
RE: Diminutive Dovetail chisels - Scoony - 03-26-2020
The one I have is a Czech Edge chisel. Works great. My only complaint was that the side edges were sharp enough to slice up my fingers pretty good. I tired to ease the edges with a stone, but ended up having to wrap the blade with blue tape to protect my fingers. Looking at his web page, seems he is not making them any more.
Glad someone is making them, and yours look great.
What I really like about these short chisels is that is less stress on my wrists to hold them upright. May not seem like a big deal, but with arthritis, the small things help a lot.
RE: Diminutive Dovetail chisels - Ron Brese - 03-27-2020
(03-26-2020, 07:24 PM)Aram Wrote: Ron,
Those are gorgeous. Would you consider making a narrow one under 1/8" Say, 3/32" or thereabouts?
Aram it's just nearly impossible to hold a piece for milling etc. that is less than 3/16" wide. It's possible to take a 3/16" and re-shape the tip but by the time one does that the cost adds up considerably. I'll noodle in it and see if I can devise a way.
Ron
RE: Diminutive Dovetail chisels - Ron Brese - 03-27-2020
(03-26-2020, 08:00 PM)Scoony Wrote: The one I have is a Czech Edge chisel. Works great. My only complaint was that the side edges were sharp enough to slice up my fingers pretty good. I tired to ease the edges with a stone, but ended up having to wrap the blade with blue tape to protect my fingers. Looking at his web page, seems he is not making them any more.
Glad someone is making them, and yours look great.
What I really like about these short chisels is that is less stress on my wrists to hold them upright. May not seem like a big deal, but with arthritis, the small things help a lot.
Yep that's an issue with a zero land chisel and as you have done adaptations can be devised. When fitting dovetails I found myself putting down 1/4" thick chisels in order to use an 1/8" chisel for better paring access. These chisels being 1/8" thick resolved that issue for me.
Ron
RE: Diminutive Dovetail chisels - Gary G™ - 03-27-2020
Looks like jewelry!
RE: Diminutive Dovetail chisels - Aram - 03-27-2020
(03-27-2020, 08:04 AM)Ron Brese Wrote: Aram it's just nearly impossible to hold a piece for milling etc. that is less than 3/16" wide. It's possible to take a 3/16" and re-shape the tip but by the time one does that the cost adds up considerably. I'll noodle in it and see if I can devise a way.
Ron
Thank you, Ron. I'm not surprised by your answer. I had to ask though -- we do make these skinny tails from time to time!
RE: Diminutive Dovetail chisels - Derek Cohen - 03-27-2020
(03-27-2020, 08:04 AM)Ron Brese Wrote: Aram it's just nearly impossible to hold a piece for milling etc. that is less than 3/16" wide. It's possible to take a 3/16" and re-shape the tip but by the time one does that the cost adds up considerably. I'll noodle in it and see if I can devise a way.
Ron
Ron, obviously it is doable. Both Blue Spruce and Veritas make 1/8” and 3/16” wide chisels with minimal lands. I’d like to see you competing with them. It seems to me that a magnetic work holding jig would be needed. I managed to bodge up something to do this myself, which was fine for one or two skinny blades I made some years ago. I look forward to you building something to do this task.
Regards from Perth
Derek
RE: Diminutive Dovetail chisels - BC in CT - 03-30-2020
Ron, those are absolutely stunning tools, must put a smile on your face every time you use them!!! Outstanding work!
Brian