+- Woodnet Forums (https://forums.woodnet.net)
+-- Thread: Top-Notch Plywood Blade? (/showthread.php?tid=7360683)
RE: Top-Notch Plywood Blade? - KLaz - 02-05-2021
I use the Forrest Duraline Hi-A/T. Zero tear out the bottom side of ply. Highly recommend although a bit pricier than the Freud
RE: Top-Notch Plywood Blade? - cputnam - 02-05-2021
U had a 96 tooth Freud Ultimate cutoff blade on the mother saw that I no longer have. It produced finish cuts - glassy smooth. Double-sided, expensive veneered plywood is a different beast though. The Forrest Duraline has cropped up in my research but, as always, the question is how much of that $$$ price is performance and how much is name - and is the performance better than the Freud, or Amana even.
RE: Top-Notch Plywood Blade? - kurt18947 - 02-07-2021
I needed to cut some melamine and experimented a bit. I made two passes, the first being a scoring cut maybe 1/16" deep then a second thru cut. Some higher end table saws have a second smaller scoring blade. I was afraid of getting a "step" where the two passes were not aligned well but making two passes worked out well. I was working against the fence. I could not envision making two passes with a miter gauge for example.
RE: Top-Notch Plywood Blade? - ®smpr_fi_mac® - 02-07-2021
Pricey but worth every penny on plywood:
https://www.amazon.com/dp/B07L9F4HLG/ref=cm_sw_r_cp_apa_fabc_MRVEM41M3ES5DT5E18BN?_encoding=UTF8&psc=1
RE: Top-Notch Plywood Blade? - Wild Turkey - 02-08-2021
The critical thing in a plywood, etc blade is that it is an "High Alternate Top Bevel (HiATB)Tooth Design"
I've used a couple and there's nothing like them for plywood.
Be careful when changing -- those "Hi" points are wicked sharp!!!
RE: Top-Notch Plywood Blade? - KyleD - 02-08-2021
I like a HiATB blade as well. But a good blade is only part of the equation for getting splinter free plywood cuts top and bottom. A proper and level zero clearance insert and steady feed rate are just as important.
RE: Top-Notch Plywood Blade? - Bill_de - 02-08-2021
(02-07-2021, 06:43 PM)®smpr_fi_mac® Wrote: Pricey but worth every penny on plywood:
https://www.amazon.com/dp/B07L9F4HLG/ref=cm_sw_r_cp_apa_fabc_MRVEM41M3ES5DT5E18BN?_encoding=UTF8&psc=1
It would probably cost too much to cut it to fit into a 10" table saw.
RE: Top-Notch Plywood Blade? - ®smpr_fi_mac® - 02-08-2021
Yeah, I noticed that it linked to the 12" blade, too.
Get the 10" one!
RE: Top-Notch Plywood Blade? - Ray Newman - 02-09-2021
Agree with what Smp_Fi_Mac posted about the Forest plyw'd.
I 've been running the Forrest Woodworker II ply-Veneer, 10", 70 teeth for about two years now. Even on the lowest grade plyw'd, the cuts are outstanding.
The only downside besides the price is that the blade is extremely sharp and it is very easy to cut yourself when installing or removing it from the arbor. Found this out the hard way and now wear gloves when installing or removing.
RE: Top-Notch Plywood Blade? - ®smpr_fi_mac® - 02-09-2021
Yup, I knicked myself TWICE the first time I installed it. I'm glad I picked up a second saw for super cheap (not much more then the cost of the blade!) to be a dedicated cross cut saw!