+- Woodnet Forums (https://forums.woodnet.net)
+-- Thread: Something to build with (/showthread.php?tid=7369774)
RE: Something to build with - bandit571 - 07-09-2022
Time to get caught up, a bit....back of the desk needed planed...
[attachment=43255]
Junior Jack took care of that...
[attachment=43256]
Then marked the board for width...
[attachment=43257]
Was kind of hoping I'd get rid of that knot...oh well...set this in the vise..
[attachment=43258]
Joint the edge down to the line....leave this sit a spell..
Dig out the Socket Maker..
[attachment=43259]
That fence was going to get moved quite a few times..
[attachment=43260]
Sockets done on all four ends....ready to be traced around, to make the matching Tails...
Stay tuned..
RE: Something to build with - bandit571 - 07-09-2022
Friday night..got bored...decided to put in a little more shoptime...until the cramps return...
Traced around a set of sockets...
[attachment=43261]
Fine tuned the traced lines with the bevel gauge/square..take the board over to the bandsaw..cut on the waste side of the lines ...
[attachment=43262]
Back to the bench, cut a knife wall, then chop a bit on the show face..
[attachment=43263]
Flip the board over, and finish the chopping..
[attachment=43264]
Test the fit...
[attachment=43265]
There was an issue with one of the sockets not quite deep enough....fixed that one.
Repeat for the other end of this board..
[attachment=43266]
This time around, 2 out of 4 sockets were not deep enough....grrrr..
[attachment=43267]
By this time, I was getting a bit sore....decided to put a couple clamps on things..
[attachment=43268]
And see how things are looking...and that was it for Friday night
Stay tuned..
RE: Something to build with - bandit571 - 07-10-2022
Saturday...after the yard got mowed, after the weeds were whacked....after the Boss was taken to Wal E World and back...THEN I spent a little bit of shop time..
Tracing more sockets..
[attachment=43277]
Bevel gauge to "refine the lines" to I can see them,
[attachment=43278]
Then the bandsaw, to cut on the waste side of the lines...trying to leave the lines...
[attachment=43279]
Add the knife wall...first chops are on the "show" side/face..
[attachment=43280]
Just enough that there won't be any blow-outs, when I chop from the other face
[attachment=43281]
Then, try a test fit...starts well enough..
[attachment=43282]
But....
[attachment=43283]
Refuses to set all the way down? Hmmmm....
[attachment=43284]
A few whacks of a chisel...and, clean out the crumbs, this time..
[attachment=43285]
That's a little better? Repeat for the other corner....
[attachment=43286]
And a full Dry Fit...
So...sometime today ( IF the Boss allows..) I can take all of this apart, set up the Stanley 45 to plough a 1/4" x 1/4" groove along the bottom edges of the sides, to house a 1/4" plywood panel....And see if that will be enough for one day....
Stay tuned...
RE: Something to build with - bandit571 - 07-11-2022
Stanley 45 is set up..
[attachment=43306]
Had to build 4 different jigs...one per side...as each side is different...
[attachment=43307]
whether it be for width..
[attachment=43308]
or an angled edge..
[attachment=43309]
Being different direction..( and a different length side)
[attachment=43310]
Then dry fit a couple sides, to mark out where to cut the plywood panel..
[attachment=43311]
Bandsaw leaves a wavy line, Junior Jack soon straightens out..another dry fit, with the plywood..
[attachment=43312]
Then take this all apart, add the glue, cauls and clamps..
[attachment=43313]
And a square to check all the corners...
[attachment=43314]
Close enough for the girls we go with?
Sunday was a bit busy....floor had a slight "Krunch" to it...
[attachment=43315]
Swept this mess up, called it a day....let this sit a day..
Stay tuned..
RE: Something to build with - bandit571 - 07-13-2022
Ok..up-date....clamps came off...needed to work on the glue joints..
[attachment=43347]
The top needed a bevel as well...
[attachment=43348]
Before it was glued into place...
[attachment=43349]
Let this sit a day....then see about a matching bevel for the lid...
[attachment=43350]
Then tried to level things up a bit...
[attachment=43351]
Then got into way too big of a hurry....and fought the hinges...
[attachment=43352]
Yep, these.....kept wondering WHY things weren't lining out....pilot holes for the screws wound up being stripped out....took a long break..
Came back to the shop.....looked things over......lid was upside down...Grrrrr.. Hinges were trashed...new ones dug out...and surface mounted..
[attachment=43353]
These will be "Stand-ins" for now....until I get better ones. And maybe inlay/inset them. Front of the lid had a small sliver split off....decided to do a round-over along the edge..
[attachment=43354]
Not much...
[attachment=43355]
Which bring things up to today's Follies....
Stay tuned..
RE: Something to build with - BpB123 - 07-13-2022
(07-13-2022, 05:51 PM)bandit571 Wrote: Ok..up-date....clamps came off...needed to work on the glue joints..
The top needed a bevel as well...
Before it was glued into place...
Let this sit a day....then see about a matching bevel for the lid...
Then tried to level things up a bit...
Then got into way too big of a hurry....and fought the hinges...
Yep, these.....kept wondering WHY things weren't lining out....pilot holes for the screws wound up being stripped out....took a long break..
Came back to the shop.....looked things over......lid was upside down...Grrrrr.. Hinges were trashed...new ones dug out...and surface mounted..
These will be "Stand-ins" for now....until I get better ones. And maybe inlay/inset them. Front of the lid had a small sliver split off....decided to do a round-over along the edge..
Not much...
Which bring things up to today's Follies....
Stay tuned..
It’s looking good!
I appreciate you sharing the journey!
RE: Something to build with - bandit571 - 07-14-2022
More of a PIP, but...
[attachment=43358]
A coat of Witch's Brew Stain has been brushed on...
[attachment=43359]
A few details have been added, it wold seem..
[attachment=43360]
Something to keep the pad from sliding off...
[attachment=43361]
Something to keep the lid shut....open the lid...
[attachment=43362]
The dividers were spaced to a perfect fit of a yellow "Legal" pad in the middle....and maybe some 3"x 5" index cards...and a few pens, pencils...
[attachment=43363]
Have since given this a second coat of stain..and wiped that down...waiting to see how that dries...
Stay tuned..
RE: Something to build with - Arlin Eastman - 07-14-2022
Boy o boy the wood looks great and the box came out as nice as well.
Have you ever made some chairs before?
RE: Something to build with - bandit571 - 07-14-2022
Have made one Rocking chair over the last 10 years.....
RE: Something to build with - bandit571 - 07-15-2022
New hinges have been installed...
[attachment=43376]
They are thin enough, that I can just surface mount them..
[attachment=43377]
And then, I brushed a seal coat of Amber Shellac ....letting it dry a while....maybe after Lunch, today....I can rub it down with some 0000 steel wool, wipe that down...then..
[attachment=43378]
One nice (maybe?) thing about taking all these photos....
[attachment=43379]
Defects you might have missed, show up quite well for the camera.....so, while I was installing the new hinges...I cranked THAT screw down tight...
We'll see how today goes.....stay tuned..