+- Woodnet Forums (https://forums.woodnet.net)
+-- Thread: Eggy water (/showthread.php?tid=7374581)
Pages:
1
2
RE: Eggy water - Gary G™ - 12-24-2023
(12-23-2023, 08:04 PM)Snipe Hunter Wrote: …. WH ….
Yep; anyway, how long should an anode last?
RE: Eggy water - Snipe Hunter - 12-24-2023
(12-24-2023, 06:22 PM)Gary G™ Wrote: Yep; anyway, how long should an anode last?
It depends on your water and I think it may depend on if your in and out pipe are properly bonded. I've had them last as little as 4 years at the old house. The Aluminum/Zinc anode I replaced it with lasted about twice that long. That well had great tasting water but had a PH problem. I don't know if fixing the PH or using the Aluminum/Zinc anode or properly bonding the pipes did the trick or all three. More on bonding here
![[Image: wU6UITy.jpg]](https://i.imgur.com/wU6UITy.jpg)
RE: Eggy water - Gary G™ - 12-31-2023
BLUF: need to know the best way to cut the old anode.
Revenge of the plumbing gods—I ordered the replacement anode after getting specs from the manufacturer and ordering from a supply house.
It didn’t dawn on me the 50 gallon tank wouldn’t have enough ceiling clearance to remove and install a new 42” long anode.
I drained the tank, pulled the existing rod out as far as possible (35”) and cleaned it as good as I could. Then, refilled the tank and we’ve used lots of hot water.
There’s no more smell.
If it returns, I’ll replace the anode rod with a 33” but I’ll need to cut the old one to remove it.
RE: Eggy water - Tim in Indiana - 12-31-2023
(12-31-2023, 06:26 PM)Gary G™ Wrote: BLUF: need to know the best way to cut the old anode.
Revenge of the plumbing gods—I ordered the replacement anode after getting specs from the manufacturer and ordering from a supply house.
It didn’t dawn on me the 50 gallon tank wouldn’t have enough ceiling clearance to remove and install a new 42” long anode.
I drained the tank, pulled the existing rod out as far as possible (35”) and cleaned it as good as I could. Then, refilled the tank and we’ve used lots of hot water.
There’s no more smell.
If it returns, I’ll replace the anode rod with a 33” but I’ll need to cut the old one to remove it.
It's soft, you can cut it with a hacksaw.
Also they sell flexible, segmented anode roads for low clearance conditions. They have the aluminum or magnesium rods cast on a flexible steel cable thay allows you to bend it every foot or so to get it into the tank.
RE: Eggy water - Gary G™ - 12-31-2023
(12-31-2023, 07:00 PM)Tim in Indiana Wrote: It's soft, you can cut it with a hacksaw.
I can do this.
When the time comes….
Thanks
RE: Eggy water - Snipe Hunter - 01-01-2024
Segmented aluminum/zinc anode Link
Double check the nipple size
RE: Eggy water - Mr_Mike - 01-02-2024
I replaced my anode rod with an electric rod. Sulphur smell is gone. I'm also on a well with a water softener and low micron filters and still had some problem before changing the anode rod.
RE: Eggy water - bmich - 01-14-2024
(01-02-2024, 05:23 PM)Mr_Mike Wrote: I replaced my anode rod with an electric rod. Sulphur smell is gone. I'm also on a well with a water softener and low micron filters and still had some problem before changing the anode rod.
Same here, I have this one. https://www.corroprotec.com/powered-anode-rod/#
RE: Eggy water - Gary G™ - 01-15-2024
For the time being, we no longer have any smell.
If it returns, I’ll look into this option.
RE: Eggy water - FireWood - 02-12-2024
I had this when I moved into this house. Like the rest of you, well water, softener, intermittent smell in the hot water, etc.
Tests on the well came up Aces, on every criteria, even on the extended $$ tests. The cold water lines ran crystal clear, no odor, no taste.
During the move-in, I had the old furnace and water heater replaced, and the smell went away. The plumber confirmed the statements above that the smell was from bacterial growth. He said that the new tank would solve the problem, and that maintaining the indirect water zone at a higher temp would prevent it from returning.
~2.5 years later and he seems to have been correct.