Something for August - Printable Version +- Woodnet Forums (https://forums.woodnet.net) +-- Thread: Something for August (/showthread.php?tid=7376479) |
RE: Something for August - bandit571 - 08-13-2024 Lets see..Disston No. 4 Backsaw [attachment=52197] With a ruler..afraid the "horns" on mine are a bit chewed down... [attachment=52198] You can make yours as long as you feel like...This handle works best with the index finger riding along the outside of the handle, with the other 3 fingers inside the grip.. Yes, I does have the Disston & Sons Medallion... [attachment=52199] Been a well used saw, over the years... RE: Something for August - bandit571 - 08-14-2024 A few details... [attachment=52211] When I do a lay out on the end of a board...I like to have it up to about eye level... [attachment=52212] As things are easier to see when I don't have to bend over to work.... However, when it comes time to use the saw... [attachment=52213] I will "drop" the board down to where the baseline is just above the jaws in the vise...maybe an 1/8" clearance? That way, the saw works easier, without any vibration going on in the wood... Sometimes, I leave a little too much of the lines...any then the dry fit...doesn't....Then I have to peel away any excess until.. [attachment=52214] Still needed to "hammer" this together... As for checking for square? [attachment=52215] I make sure it is square this way...sometimes, one corner will not seat all the way in... I still check the fit, with the "upright" held plumb.. [attachment=52216] So...Dovetails #2 is completed... [attachment=52217] Making sure the box will match the doors.... [attachment=52218] The "Top" of the box needs to be done, next....so that the doors have support.... Pins for corner #3 have been laid out....so I guess I had better get to work.. Stay tuned... RE: Something for August - bandit571 - 08-14-2024 Dry fit, corner #3.. [attachment=52220] then for Corner #4..there was a question.. [attachment=52221] Hmmm, will they fit? [attachment=52222] I guess so.... Now that the corners are all done...need to get this plane set up, again.. [attachment=52223] Because a I need a rebate made....to set the 1/4" plywood back into... [attachment=52224] Along with a way to hold the parts steady.. [attachment=52225] Leg vise at one end, and a 12" clamp at the other, hooked into the tool well... 1 done, 3 more to do... RE: Something for August - Bob10 - 08-14-2024 Are you going to paint that wall before you put that up? RE: Something for August - wing nut - 08-15-2024 (08-14-2024, 08:55 PM)Bob10 Wrote: Are you going to paint that wall before you put that up? If you do don't forget to paint behind the toilet. RE: Something for August - bandit571 - 08-15-2024 Ok...for one thing...I do NOT paint..anything.. Plan for today.....need to get these 4 items glued up... [attachment=52227] Into a frame...so I can lay out and cut a plywood panel for the back of the case...and work on the Top Shelf, and the inside stuff... Any painting will be up to the Boss...and she alone... RE: Something for August - bandit571 - 08-15-2024 There was cussing involved, but.. [attachment=52228] Glued up...I might have used just enough clamps... [attachment=52229] That diagonal clamp was to pull the case into square...was about 1/8" out... [attachment=52230] There is not a whole lot of room, down here in the shop Will let this sit a spell.. Stay tuned.. I did say something to the Boss about those "painting" comments....and you 2 did give her a very good laugh... RE: Something for August - stav - 08-15-2024 I'm with you. I don't do painting at my place unless I have to. My wife is an artist and painting is her thing. Most times, I don't even get input in color choices. RE: Something for August - bandit571 - 08-16-2024 Box is out of the clamps...will let it sit a few more days, before I clean up the glue joints...since I also installed a rail to hang this box to the wall's studs.. [attachment=52264] Once this is also dried....I can cut and fit a 1/4" plywood back.....needed to rail to be flush with the bottom of the rebates... I added 2 screws.. [attachment=52265] Since there is a top shelf going onto this board..attached from the inside of the box...with a few screws...might also just glued it down with a few clamps, too.. Have bought the hinges to both install the Towel Rack...but also to attach the doors.. [attachment=52266] Once I get the doors fitted to the case... Stay tuned... RE: Something for August - bandit571 - 08-16-2024 Ok..working way too hard for a Friday....but.. [attachment=52268] 1/4" Plywood panel has been cut and notched to fit....then glued and screwed into place... Notched? [attachment=52269] Because the rebates left those openings (gaps) at the corners...filled up with the plywood...and will "disappear" once the stain goes on... Worked on building a frame to house the 3 rods that towels will get draped over... [attachment=52270] Rods are a TIGHT fit, with a 12/16" bit.. [attachment=52271] Only need to go 3/8" deep. Back of BOTH knees are sore and crampy...may have to go to the store and buy a bottle of Tonic Water...to make tonight's Tonic & Gin? Stay tuned.. |