+- Woodnet Forums (https://forums.woodnet.net)
+-- Thread: Pine Inventory (/showthread.php?tid=7338561)
RE: Pine Inventory - Bob10 - 04-14-2018
You need one of these on the feed to that pit, good work on that clean up just noticed the water tank with a standing pilot
![[Image: image_26462.jpg]](https://shop.harborfreight.com/media/catalog/product/cache/1/image/9df78eab33525d08d6e5fb8d27136e95/i/m/image_26462.jpg)
RE: Pine Inventory - bandit571 - 04-14-2018
Yep, I share the basement with a gas water heater, and a gas forced air furnace....and the Boss's laundry Room stuff.
Plus, half the basement is storage for stuff....need to clear that out...sometime. 
RE: Pine Inventory - alanealane - 04-15-2018
Hope the toasted spokeshave was restored ok! It sounds like something that would happen to me so forgive me for chuckling a little bit
RE: Pine Inventory - bandit571 - 04-15-2018
Rehabbed spokeshave
[attachment=9888]
Even rehabbed the sole..
[attachment=9889]
iron is sharpened back up ( was needing it, anyway) and the logo..
[attachment=9890]
Used a Gun Blue paste, instead of black paint.....had to take the item all the way back to bare metal....gun blue worked nicely.
been busy on the Rust Hunt Trail....maybe Tuesday, I can go back to making sawdust?
RE: Pine Inventory - Arlin Eastman - 04-17-2018
(04-14-2018, 03:02 PM)bandit571 Wrote: Yep, I share the basement with a gas water heater, and a gas forced air furnace....and the Boss's laundry Room stuff.
So how is the house hunting going for you? So hope you get a nice big shop in the future.
RE: Pine Inventory - bandit571 - 04-18-2018
Afraid we be stuck here for a while....unless something drastic happens.....Spent some time rehabbing one of the trophies from the shop clean up...
[attachment=9937]
This is what was found...the Stanley #4 is for scale.....made about 1863 or so. Just an old plough plane. Was trying to use it a few years ago, got ticked off with it not hold a setting..tossed it into a corner....and decided to get a Stanley 45 instead...
Well..since this big clean-up..decided to try to fix it up, and see IF I can get it to work, again..
fence was broken, wedges were too small...handle was snapped off.....found a decent chunk of Maple for the handle, had a slab of Ash for the fence replacement...new wedges were made out of walnut....iron was sharpened up, and a groove cut in it to guide onto the skate...
[attachment=9938]
Replacement fence needed a rebate planned, new bolts ( old, 1860 ones were shot) one of the arms needed fixed ( pedestal was cracked by one of the screws, re-glue) New wedges needed tuned all three of them. One for the cutter needed thinned to match the cutter. Two for the fence's arms needed to match the tapered holes. Whew..
[attachment=9939]
A new handle was cut out of the maple block, then ripped for thickness. Shaped to match my hands better, and LOOK like a plane's rear handle. Base of the handle fitted into a mortise. At one time, it was dovetailed in....since worn out. Rather than just relying on glue, I added a screw to better hold the handle in place...
[attachment=9940]
Once everything had been cleaned up, rebuilt, sharpened, and tuned up....and a coat of Golden Oak and a coat of Amber Shellac was brushed on....then the test drive. Set the fence to 1/4" in from the edge. and ploughed a 1/4" wide groove. There wasn't a depth stop on this plane, when it bottomed out, you were done.
[attachment=9941]
Shavings tend to spiral out the right side of the plane..making some nice curlies. Not too bad, for an old Plough plane?
RE: Pine Inventory - hbmcc - 04-18-2018
Cool save, Bandit! But, but..... now the pine will have grooves. Plate display shelf, perhaps?
RE: Pine Inventory - Arlin Eastman - 04-18-2018
You did a swell job on rehabbing the plane!
RE: Pine Inventory - TomFromStLouis - 04-19-2018
That is a truly spectacular save on that plough plane.
RE: Pine Inventory - bandit571 - 04-21-2018
(04-18-2018, 09:39 AM)hbmcc Wrote: Cool save, Bandit! But, but..... now the pine will have grooves. Plate display shelf, perhaps?
Maybe needs a Match plane, to make a tongue & groove corner joint?