+- Woodnet Forums (https://forums.woodnet.net)
+-- Thread: Using the leftovers (/showthread.php?tid=7356408)
RE: Using the leftovers - bandit571 - 08-06-2020
Stain has arrived..Minwax "Gunstock". Has been brushed on, then, wiped down once everything was coated...
[attachment=28883]
Intend to "line" the inside
[attachment=28884]
With a foam padding...this IS a toolbox, after all..
[attachment=28885]
Good thing this IS the back of the box, and will be against a wall...
[attachment=28886]
Trying to decide on whether to add a chain to the lid...
[attachment=28887]
Or..not....kind of on the thin side...trying to find screws wide enough, that won't poke through the lid or the sides...
Will be looking for a couple handles for the ends, to help carry this thing....there will be a special bit of "trim" right above the upper center drawer...once the finish is done...
Stay tuned..
RE: Using the leftovers - bandit571 - 08-07-2020
Waiting on the stain to stop smelling the place up...then I can do the varnish part..
Well, and how does one install this stuff...?
[attachment=28891]
Just lay in in there? line all the sides, as well.....glue used?
May just cut to fit... and flop it into the wet varnish....or, just leave it loose...
Stay tuned...
RE: Using the leftovers - MarkSingleton - 08-07-2020
I just cut it to fit and lay it in there. Never had a piece jump out yet.
RE: Using the leftovers - bandit571 - 08-07-2020
Hmmmm. one on the lid, and one on the front, above the center drawers?
[attachment=28908]
Make a couple labels?
[attachment=28909]
These come 3 to a baggie, with screws...
RE: Using the leftovers - Arlin Eastman - 08-08-2020
It sure looks good to me.
RE: Using the leftovers - bandit571 - 08-08-2020
Single coat of clear gloss has dried, and been rubbed down...Label holder installed, and figured out the chain install...
[attachment=28916]
Oh, and a foam pad was cut to fit. Then these took up "residence"...
[attachment=28917]
Closed the lid, before any more show up...
[attachment=28918]
Still on the look out for a pair of handles I like, that will fit on the ends...
[attachment=28921]
Install with screws ( can't access the inside very well) and match the rest of the hardware...
[attachment=28922]
maybe print or draw up a label to sit in the holder?
Just might be done? Was supposed to be done before Aug. 1st....I was.."delayed"...
Thanks for looking...
RE: Using the leftovers - bandit571 - 08-09-2020
Handles were bought, today....needed modified to what I needed. They were to use a bolt from the inside of the case.....not an option here. There were two FAKE screw heads on the outside..were being the operative word. ground those off flat. There was a dimple in the back...got out a couple drill bits...one broke before I finished the first hole! Over in the Tap & Die Box, there was a brand new, SHARP drill bit about the right size...drop or two of oil...did 3 holes in the same time as the first one did..
So, holes drilled, fake screws gone...and some of the paint....paint the entire handle black...and then rehab a saw while I wait on paint to dry..
Then, haul the handles and their new screws upstairs, and install on the ends of the case..(picture time!)
[attachment=28933]
hard parts...getting this level...and then..[attachment=28934]
Getting the other one to match...
Tray is filling up..
[attachment=28935]
And, so are some of them drawers...going to be a hefty case...
Oh, as for that saw?
[attachment=28937]
That Estate Sale $1 D8 Rip saw....might find a use for it...