+- Woodnet Forums (https://forums.woodnet.net)
+-- Thread: Daily Bench Shot (/showthread.php?tid=7336585)
Pages:
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
RE: Daily Bench Shot - Belle City Woodworking - 08-24-2018
(08-24-2018, 10:58 AM)Stwood_ Wrote: Ah I see now. Guess they were copying tools back then too.
i think so
RE: Daily Bench Shot - Belle City Woodworking - 08-24-2018
With some help I flipped the tabletop and got to work on the bottom of the table. I also found the straightest board in the pile of salvaged lumber for the breadboard ends and I got those roughed out. I will get to work on the mortise and tenons and will secure them with draw bores.
![[Image: XMRY4dc2_Qzy_Az_Dw8o_Lg.jpg]](https://s26.postimg.cc/4p3lqa3o9/XMRY4dc2_Qzy_Az_Dw8o_Lg.jpg)
I am convinced that this is about the biggest project I would be able to do in my basement shop
RE: Daily Bench Shot - Stwood_ - 08-24-2018
Time to stop and fix some air guns. One 16ga., two 18ga., and a 1/4" crown stapler.
Stapler I just cleaned up and greased the o-rings.
[attachment=12509]
The 16ga needed a driver bumper and a seal. $31.00 for those 2 pieces of plastic laying by the hex T wrench.
RE: Daily Bench Shot - EdL - 09-05-2018
Had to put a diaghpram kit in the carb for my brushcutter.......made it 21 years.
Ed
RE: Daily Bench Shot - titanxt - 09-09-2018
Mine is currently covered with the last of my machine tooling.... It is being sold and going out the door so I can get back to some relaxation and peaceful woodworking!! It is good to be back!
![[Image: S1DmxJMl.jpg]](https://i.imgur.com/S1DmxJMl.jpg)
RE: Daily Bench Shot - Stwood_ - 09-09-2018
Spent the day fixing the rest of my nail guns that had quit, or needed attention.
$60.00 in parts and five more are back in service. These are all the older series guns that I feel are better than PC's current lineup of air guns, so I'm keeping them around.
[attachment=12876]
I also got my BBQ spatula re-riveted.
Fuzzy picture. I need a new camera.
RE: Daily Bench Shot - EdL - 09-09-2018
Got our "team Bancroft" sawmill running today, been 4 years since I used it. Need to clean the crap out of the mill shed yet.
My first load of way overdoo to mill logs is on the trailer. 3 white oak & 5 cherry, going to be lots of lost lumber from setting, it is what it is. Nobody's fault but mine.
Ed
RE: Daily Bench Shot - Stwood_ - 09-09-2018
Paint the ends.................
Nice trailer...........
RE: Daily Bench Shot - EdL - 09-09-2018
(09-09-2018, 11:31 PM)Stwood_ Wrote: Paint the ends.................
Nice trailer...........
Paint isn't going to do anything when the logs sit for 4 years.
This load should be decent on the yield, the red oak won't be pretty, already lost the soft maple & walnut.
The trailer is the deckover from he11, 18' lg and 4k lbs. The frame is 12" I-beam, slightly overkill.
Ed
RE: Daily Bench Shot - Stwood_ - 09-09-2018
(09-09-2018, 11:37 PM)EdL Wrote: The frame is 12" I-beam, slightly overkill.
Ed
Uuummm yea. Bet it rides good though. No bounce....