+- Woodnet Forums (https://forums.woodnet.net)
+-- Thread: another build thread... (/showthread.php?tid=7335748)
RE: another build thread... - bandit571 - 01-09-2018
Not a whole lot got done, today
I figured up how long to make the panel for the door's raised panel. Had two planks about that length IN the shop, but needed a third...
Trudged back upstairs, and hauled a plank to the shop....whew. Cut a section that actually looked flat....
Strated jointing all the edges..( I thought) until most matched each other. Width was quite right, had to add a 2" wide strip. Spalted edges will go to the outside edge. Test fit in a couple pipe clamps....Hmmm, a gap? Took that board out, slammed it into the crochet, and added a c clamp....edge was worked over until that gap went away...ankle deep in shavings, from all this plane work ( or, is it just plain WORK?)
Another test fit....no gaps, a couple high spots I can plane down later.....spread some glue around, and clamped things up, including a third pipe clamp on the top..
[attachment=7073]
Third clamp is to get things from bowing up.....compost happens....the high spots?
[attachment=7074]
Show up as shadow lines....we have ways ......maybe tomorrow, I can get this out of the clamps, and trim it to size, and start raising it.
Unless I get bored tonight, glue up can just sit right there.
Stay tuned...
RE: another build thread... - bandit571 - 01-10-2018
Ok, busy day, today...got the panel out of the clamps. Needed to rip it to size, then do a bit of jointing, to remove the saw marks.
[attachment=7115]
And, worked on some of the high spots...
[attachment=7116]
Then clamp the panel so I could bevel the end grain....
[attachment=7117]
jack plane did most of the work, the #4 then cleaned things up...
[attachment=7118]
Once both end grains were done, then I beveled the edge grain as well....Makes a nice corner detail...
Had to flip the panel over, and work on the "inside" of the panel...
[attachment=7119]
Had to keep sweeping the floor,was getting a bit deep. Raised part is done.
Stay tuned, as I needed more work to be done...
RE: another build thread... - bandit571 - 01-10-2018
Ok, panel was a bit on the thick side, decided to add a rebate on the "inside" of the panel..
[attachment=7120]
Something like this. On the end grain. I used the Wards(Stanley) #78..
[attachment=7123]
Got both ends done. The spur on a #78 doesn't do that well, on edge grain, soooo
[attachment=7124]
I set up the Stanley 45 to make the same cuts..without the spurs.
[attachment=7125]
Got all four rebates done....set the panel aside, and set up for a few mortises..
[attachment=7126]
Stay tuned, more to come....was a very busy day..
RE: another build thread... - bandit571 - 01-10-2018
Needed four mortises chopped...mortise chisel...
[attachment=7127]
Ash was a bit rough on this one, had to bring out a few others...finally got a mortise to test fit..
[attachment=7128]
The a couple more, and a dry fit..
[attachment=7129]
Then got the last ones done...
[attachment=7131]
Door is actually laying on it's side. Placed it in the end vise, so it could help hold things while glued and clamped it..
[attachment=7132]
Will let this sit a while....for some reason, I am a bit tired
Stay tuned
RE: another build thread... - Tynyyn - 01-10-2018
Did you show how you did the bevels? I'm too lazy to look back.
RE: another build thread... - bandit571 - 01-10-2018
(01-10-2018, 07:44 PM)Tynyyn Wrote: Did you show how you did the bevels? I'm too lazy to look back.
Use the same way that Paul Sellers does. Except I have the panel flat on the bench. I go at a diagonal to the grain. I do the end grain first, then the edge grain. Edge grain..I simply hold the plane at an angle, and start working from the edge's top into a bevel.
RE: another build thread... - bandit571 - 01-12-2018
PIP: Door is now installed..
[attachment=7187]
RE: another build thread... - Rick Barton - 01-12-2018
Its really coming together now.
RE: another build thread... - Tynyyn - 01-12-2018
You get a nice pat on the back. I wish I could do things like that. I just lack ambition after a day of working for 'da man.
RE: another build thread... - bandit571 - 01-12-2018
Retired soon to be 3 years ago....
Was going to try out a couple jointers, and call it a day...
[attachment=7207]
Trying to get this board ready to use..
[attachment=7208]
Kept thinking about it....finally i hauled another plank to the shop..the last plank I have...D-112 handsaw to do the rough crosscuts
[attachment=7209]
Then marked each up, and trimmed them until they matched each other...except in thickness...
There was enough "good" wood left over, that a top shelf could be cut to size....had a small problem
[attachment=7210]
It has a small knot..
not too bad, does not go all the way through I need to go back to my friend's shop, and buy a couple more planks of this Ash. Face frame, shelves, and another door....
Will have to see IF I have anything to use as a back for it.
Stay tuned....