+- Woodnet Forums (https://forums.woodnet.net)
+-- Thread: Spoon carving video (/showthread.php?tid=6982469)
Spoon carving video - Timberwolf - 03-26-2015
Using a hook knife....
https://www.youtube.com/watch?v=jpnx9kuZeqg
And another
https://www.youtube.com/watch?v=6rZK3WLTse4
Re: Spoon carving video - Ohio Mike - 03-26-2015
Thanks
Re: Spoon carving video - AHill - 03-27-2015
The first one is interesting in that he mostly uses what is essentially a hunting knife for most of the process. Not traditional, but it seems to work pretty well. More control with that knife than I would have thought.
Re: Spoon carving video - Timberwolf - 03-27-2015
Same here... Properly sharpened hook knives are my tool of choice for hollowing spoon bowls.
Re: Spoon carving video - Arlin Eastman - 03-27-2015
Jack
How does a person make a hook in a knife?
Then how is it sharpened?
Arlin
Re: Spoon carving video - Timberwolf - 03-27-2015
Arlin, The way I do it is, I do a rough sharpening job on a piece of steel I want to become the blade...Then I heat the steel bright red {in daylight} and bend it about half way around a piece of pipe that I have clamped in my bench vise..The pipe is the diameter that I want for the hook...Then, while it is still cherry red, I quench it slowly in oil {or water, depending on the type of steel}.....I prefer the bevel to be on the outside of the blade, but I have made them with the bevel on the inside...and I have made some with a double bevel...after the steel has cooled, I "brighten" the steel with an abrasive like sandpaper, removing the oxide that forms..At that point, I temper it...I usually do that with a slow flame from the torch...I "play" the flame over the steel uniformly until the color change reaches a light "straw" yellow color.{ if one has never done it that way, an oven at ~400* will work}..At that point, the steel is tempered so that it has the best edge-holding ability, without becoming overly "brittle"..Of course, there again, it depends on the type of steel, but that's what I do when I am using O1 tool steel. From there, I do the final honing for a razor edge, and for that, I usually use my Dremel with a Cratex wheel for the inside bevel, and a fine belt on a grinder, finishing up with a leather polishing strop, for the outside..You can also sharpen the hook using the appropriate hones an/or leather wheels. . {And you can make very small LEATHER wheels for stropping the inside bevel with your Dremel.}..I can't remember ever NOT having a Dremel..I don't know how anyone does without one...
Re: Spoon carving video - AHill - 03-27-2015
Hook Knives can also be purchased:
http://www.amazon.com/Morakniv-Carving-Knife-Carbon-Steel/dp/B00343VCCK
http://www.highlandwoodworking.com/frosts163swedishhookknife.aspx
http://www.highlandwoodworking.com/flexcut-right-hand-hook-knife-kn26.aspx
Pinewood forge also makes very, very good hook knives, but they are more pricey and you may need to wait until he makes a batch. Hook knives come in right handed, left handed, and dual handed versions.
Re: Spoon carving video - Arlin Eastman - 03-27-2015
Jack
I did not know if you used a torch or forge or the thickness of the metal you used it to bend with.
I did email Gene Henrikson who makes small forges (http://walnutforge.com/Gallery.php) and he makes some really really good ones at a less then $200
Arlin
Re: Spoon carving video - Arlin Eastman - 03-27-2015
Allan
If you remember Del Stubbs the turner that is what he makes now.
http://pinewoodforge.com/
Arlin
Re: Spoon carving video - AHill - 03-27-2015
Arlin Eastman said:
Allan
If you remember Del Stubbs the turner that is what he makes now.
http://pinewoodforge.com/
Arlin
My hook knife is a Pinewood Forge. Just offering more affordable alternatives for the rest of the crowd out there. Not sure I'd spend $200 on a hook knife, though. I can't imagine it would be 4-7x better than some of those I linked to.