+- Woodnet Forums (https://forums.woodnet.net)
+-- Thread: have you seen this hinge boring jig (/showthread.php?tid=7085420)
have you seen this hinge boring jig - MstrCarpenter - 08-29-2015
I was watching a repeat of T.O.H. today and I saw the Finish Carpenter/Cabinetmaker use a jig to drill the 35mm (1 3/8") hole for the cup with a cordless drill perfectly. I have not seen this jig before, and haven't been able to find it with Google. The jig has two parts; The part you hold on the door, the base, is about 6" square with a 4" (or so) ring about an inch tall. It also has an edge guide and center index marks. The part with the bit has a ring that fits inside the ring on the base. The bit may have to be part of the jig because it slides in a bushing keeping it 90* to the door. There is also a depth stop and a spring to push the guide back out.
This is a tool that would make choosing the advantages of European Hinges over semi-concealed or butt hinges a lot more user friendly in the field. I would definitely like to have one in my bag of tricks.
If anyone has, or knows of this jig could you please post a link, picture, review, ect.?
Re: have you seen this hinge boring jig - Scoony - 08-29-2015
CMT has a cool hinge boring jig
Re: have you seen this hinge boring jig - Richard D. - 08-29-2015
Rockler
Re: have you seen this hinge boring jig - BloomingtonMike - 08-29-2015
Seen the Sommerfield or the Blum (Sommefrield may have copied Blum) Easy Hinge Boring Jig?
http://sommerfeldtools.com/sommerfeld-s-hinge-boring-jig
Re: have you seen this hinge boring jig - MstrCarpenter - 08-29-2015
Wow! That was fast. The Rockler jig uses the same concept as the one on T.O.H. but I don't think the clamp on feature they added will be of much benefit to me. I also just viewed their similar jig; minus the base and spring. At $16, I would have bought one years ago. I've made quick jigs that reference the edge, and top or bottom of the door to locate all three holes but messing with a block of wood for a depth stop was frustrating for a few pairs of hinges.
Re: have you seen this hinge boring jig - MstrCarpenter - 08-30-2015
[blockquote]BloomingtonMike said:
Seen the Sommerfield or the Blum (Sommefrield may have copied Blum) Easy Hinge Boring Jig?
So I just checked out the one Mike linked to. So now I'm at $16 for an easier depth stop. $60 for a jig that does one hole . Or $180 for a jig that does all three (if I have the hinges that use the 8mm holes). I'm leaning towards option #2, but if it's cheap plastic that won't survive being slightly abused while in transit (i.e. a 20 pound router riding on it in the van) it will be a waste of time and money.
You Guys have no problem spending other Woodnetters money.
Has anyone seen one like Rocklers made of steel?
Re: have you seen this hinge boring jig - blackhat - 08-30-2015
web page
This is an option.
Re: have you seen this hinge boring jig - BloomingtonMike - 08-30-2015
Do you often cut holes for hinges in the field?
Re: have you seen this hinge boring jig - jussi - 08-30-2015
MstrCarpenter said:
So I just checked out the one Mike linked to. So now I'm at $16 for an easier depth stop. $60 for a jig that does one hole . Or $180 for a jig that does all three (if I have the hinges that use the 8mm holes). I'm leaning towards option #2, but if it's cheap plastic that won't survive being slightly abused while in transit (i.e. a 20 pound router riding on it in the van) it will be a waste of time and money.
You Guys have no problem spending other Woodnetters money.
Oh wait but there's more. Don't forget the Festool option. The LR32 which does both the shelf pins and hinges. For a mere $495. Plus $100 for the holey guide rail and $400-$500 for the router. Only works with their router.
Of course only an person would pay that much.
<--- I own all 3 items
http://www.amazon.com/Festool-584100-Hole-Drilling-Systainer/dp/B0058HVVPI
https://www.youtube.com/watch?v=XSTQlFKtP4o
https://www.youtube.com/watch?v=L2gQVWADWq4
Re: have you seen this hinge boring jig - MstrCarpenter - 08-30-2015
BloomingtonMike said:
Do you often cut holes for hinges in the field?
Currently, only a couple times a year, but If I invested in an accurate and efficient jig, I think it would be a lot more. For built-ins, I usually make doors and face frames in the shop and drill for hinges with a drill press. There are times that they don't get drilled, and a few times they were drilled in the wrong place (Sometimes due to field conditions and sometimes just operator error.) The holes get drilled after finishing, and there's usually at least some finishing done in the field. So drilling in the field just prior to installing the hinges would eliminate a step in the shop between finishing and packaging.