+- Woodnet Forums (https://forums.woodnet.net)
+-- Thread: Kitchen cabinet design (/showthread.php?tid=7177479)
Pages:
1
2
Kitchen cabinet design - RichK - 12-26-2015
I'm planning to build a 6' run of framed upper cabinets. Instead of building 2-3 individual boxes, any reason not to build one 6' long cabinet? From the outside, the frame and doors would look no different from a typical 2-3 box design. Each shelf would be supported at the ends, each frame stile, and the back. The purpose would be to provide more flexible storage.
Any disadvantages that I'm missing?
Thanks,
Rich
Re: Kitchen cabinet design - packerguy® - 12-26-2015
I dont build cabinets, but I think size and weight work against you while trying to hang it, and probably the biggest I would think would be strength. Can you hold as much weight in a 6' box, or three 2' boxes?
Re: Kitchen cabinet design - Bit_Fiddler - 12-26-2015
I know that working by myself, it would be impossible to lift and hang a single 6' cabinet. Pretty sure the Mrs would not be enough to make a difference in that equation either....
Re: Kitchen cabinet design - MikeinKCMO - 12-27-2015
Yes it would take 3 guys to install it in a perfect world, but with a little ingenuity one can prop it up on the counter or over the floor.
Re: Kitchen cabinet design - Chataigner - 12-27-2015
RichK said:
I'm planning to build a 6' run of framed upper cabinets. Instead of building 2-3 individual boxes, any reason not to build one 6' long cabinet? From the outside, the frame and doors would look no different from a typical 2-3 box design. Each shelf would be supported at the ends, each frame stile, and the back. The purpose would be to provide more flexible storage.
Any disadvantages that I'm missing?
Thanks,
Rich
Apart from the weight, none. The advantage in my house (late 18th C) would be that the cupboards would be nicely aligned. Fitted individually on walls that are neither straight nor vertical, individual cupboards are very difficult to align correctly. I'd go for one big one.
Re: Kitchen cabinet design - deepsplinter - 12-27-2015
I would be concerned about it sagging.
Will there be a vertical partition midway?
Is it hanging from a bulkhead?
Re: Kitchen cabinet design - DaveR1 - 12-27-2015
We had a single piece upper cabinet that is about 6' long in our kitchen. It hung over the peninsula. It is divided into three section each with double doors. It was attached to the wall at one end and hung from threaded rods that went up to the ceiling at the other. It was there a long time and held dishes and other heavy stuff. Doors on both sides so there was no back panel to add stiffness. It never sagged.
I took it down when we decided to get rid of it and that wasn't pleasant but it wasn't terrible, either. I built up supports under it before removing screws. It is on the wall in my shop, now.
Re: Kitchen cabinet design - Akula - 12-27-2015
Nothing wrong with 6 foot cabinet.
But . . . I would consider an interior partition to cut down the length of the shelf. A shelf of that length will sag, absent extra engineering (e.g., tortion box design).
Scott
Re: Kitchen cabinet design - Woodenfish - 12-27-2015
There are so many more positives than negatives in building a continuous cabinet. The negatives are so easily overcome they aren't worth the time worrying about.
Re: Kitchen cabinet design - JGrout - 12-27-2015
Akula said:
Nothing wrong with 6 foot cabinet.
But . . . I would consider an interior partition to cut down the length of the shelf. A shelf of that length will sag, absent extra engineering (e.g., tortion box design).
Scott
why>
Add shelf pin supports in the front and back of the unit mullions and shelves are supported the same as a divider.
You may however have a larger issue getting the shelf in the cabinet (which you will be able to as long as there is adequate length on one side or the other of the installed unit) than you ever will with sagging done like this