crosscut sled - Printable Version +- Woodnet Forums (https://www.forums.woodnet.net) +-- Thread: crosscut sled (/showthread.php?tid=7183215) |
crosscut sled - Buckhunter - 01-03-2016 looking for a plan or ideas for a crosscut sled Re: crosscut sled - Doug_H - 01-03-2016 Richard, I built this one from Highland Woodworking many years ago when I was starting out. I have been very happy with it, except that it takes up some space to store. I bought the kit but could have just used the instructions and done without it. You could use oak guides in the miter slots. I put the plastic blade cover aside and never used it. I did make the big, laminated handle and "exit block". The handle, however you make it, is a must to keep your hands away from the blade. A stop block to prevent the blade from cutting through the front of the sled is a must. Doug Re: crosscut sled - Gary G™ - 01-03-2016 Here: http://www.forums.woodnet.net/ubbthreads...part=1&vc=1 Re: crosscut sled - LarryWilson - 01-03-2016 I looked forever on the net for a good design that I liked. I settled on this as a basic design. Super nice that it is adjustable for squareness. Not to mention that it works as a zero-clearance dado sled as well. I built a larger one and a mid-sized one. Absolutely awesome. https://www.youtube.com/watch?v=AyB9uA-Q9xY Re: crosscut sled - Cecil - 01-03-2016 Thanks Larry. Out of all the sled designs I have seen, I like this one the best. I would make one change, and that is to put a replaceable insert on the bottom too. I think it is time for me to make a sled ! Re: crosscut sled - Routerman - 01-03-2016 This one for a router. Center guide is trapped between 2 phenolic rails screwed to jig plate aluminum. Has no where to go but straight. Guides are adjustable to zero out slop. Might be an idea here for you. Re: crosscut sled - hankgillette - 01-03-2016 Gary G™ said: That’s a beautiful sled. I take it that MMarzluf is deceased? I wonder about some people who post here and then just disappear. I am sure some of them move on to other interests, have a falling out with people on the forum, or in a few cases get banned. Sometimes I see notices that someone has died, others not so much. Has anyone created a list of deceased members? I don’t post here all that much, but I don’t think any of my family knows that I do. If I were to die tomorrow, I would just disappear from the forum. My brother, who does financial planning, has been working on a paper on preparing information for your heirs about your online accounts. Perhaps I’ll check to see if he includes instructions about forums that should be notified after one’s death. As I said, I am not a very active participant, but I do read a lot more than I post, and I consider this a community with some really helpful people where I can get information and ask questions. Re: crosscut sled - jteneyck - 01-03-2016 I built the one Jerry Cary shows in his book on building kitchen cabinets before I built my kitchen. Three things his has that I haven't seen on others, that I think are critical from a safety standpoint are: 1) a plexiglas guard above the blade spannng from the front to back rest, 2) a blade guard behind the back rest so the blade can't cut your hand at the end of the cut, and 3) a forward limit stop. They all work together to reduce the probability of an accident. John Re: crosscut sled - CARYinWA - 01-03-2016 After wrestling with several sleds I found this works best for me. Light and adjustable. Re: crosscut sled - Steve N - 01-03-2016 hankgillette said: His ex wife may wish for that, but MMarzluf is just dead to WoodNet. |