+- Woodnet Forums (https://forums.woodnet.net)
+-- Thread: High Speed Dental Tool Question (/showthread.php?tid=7245041)
High Speed Dental Tool Question - badwhiskey - 03-16-2016
So, my high speed dental tool finally showed up. How do I connect between this unit and my compressor? There's a length of plastic tubing that looks like it forms a compression fit with the unit, but what parts do I have to buy to connect to the air hose coming from my compressor?
Also, does anyone know what psi I should run? The dental tool didn't come with instructions.
Thanks.
Re: High Speed Dental Tool Question - Arlin Eastman - 03-17-2016
Sorry Frank
The one I want to get that is High Speed 380,000 to 480,000 all I have to do is plug it in and use it. It has its own air turban
http://www.ebay.com/itm/361294844568?ssPageName=STRK:MESINDXX:IT&_trksid=p3984.m1436.l2649
Arlin
Re: High Speed Dental Tool Question - imapseudonym - 03-17-2016
You might want to look at that again, Arlin, that unit needs to be hooked up to an air compressor to run.
"Just connect to air compressor (0.4Mpa~0.8Mpa required) to get start"
You will likely need an adapter that will go from a typical compressor line (e.g. npt fitting) to whatever the input is on that box.
Maybe I was misunderstanding what you meant by just plug it in, but it sounded like you were under the impression that no separate compressor was needed which would make for quite a disappointing unboxing if you ordered it.
Re: High Speed Dental Tool Question - Arlin Eastman - 03-17-2016
imapseudonym said:
You might want to look at that again, Arlin, that unit needs to be hooked up to an air compressor to run.
"Just connect to air compressor (0.4Mpa~0.8Mpa required) to get start"
You will likely need an adapter that will go from a typical compressor line (e.g. npt fitting) to whatever the input is on that box.
Maybe I was misunderstanding what you meant by just plug it in, but it sounded like you were under the impression that no separate compressor was needed which would make for quite a disappointing unboxing if you ordered it.
I have been wrong many times and it seems so this time. I guess I will have to make an additional hose just for that with one of these http://www.ebay.com/itm/191759504842?ssPageName=STRK:MESINDXX:IT&_trksid=p3984.m1436.l2649
and this
http://www.ebay.com/itm/371010867099?ssPageName=STRK:MESINDXX:IT&_trksid=p3984.m1436.l2649
Would this set up do the trick
Arlin
Re: High Speed Dental Tool Question - badwhiskey - 03-17-2016
Hey, I figured it out! As was said, you need to connect the turbine unit to a compressor. Mine came with no instructions. Just the turbine in a box!
I had to warm the plastic tube with a hair dryer to get it to slide over the fitting. And the fitting I bought was with the air compressors, not in the hardware aisle as the website and HD employee told me it would be.
Re: High Speed Dental Tool Question - Ruler2112 - 03-17-2016
I got a dental drill relatively recently. I rednecked a solution to hooking it up by taking a 5' chunk of rubber brake line hose (smallest available) that just fit over the air intake on the drill (with shaving the outside so it'd fit) and then shoved the other end over the nozzle of one of my blowgun attachments. Zip-tied the trigger down & put a ball valve ($3 at harbor) to act as a switch. Planned on making something more permanent, but this is working too good to mess with, even though it's fugly.
I converted the mpa rating they gave in the directions of my specific drill to psi and it was 25-35; I have a hunch that every drill has it's own though.
Very cool using it! MUCH easier than trying to use a dremel. Biggest problems I have now is that when I pierce, my tiny HF compressor runs constantly and I tend to go from an organic skeletal pattern to ancient egyptian hieroglyphs to norse runes - gotta pick a pattern & stick with it!
Re: High Speed Dental Tool Question - Arlin Eastman - 03-18-2016
Thank you for the link Frank.
I am still going to use the Brass Air Regulator valve so it is easy at had to adjust the air pressure.
Arlin
Re: High Speed Dental Tool Question - gcrimmins - 03-20-2016
I believe that 30psi is as high as high as you want to go. Also, you'll need a simple inline oiler if there isn't one built into the control box.
--Geoff
Re: High Speed Dental Tool Question - badwhiskey - 03-20-2016
I was wondering about that.
Re: High Speed Dental Tool Question - Ruler2112 - 03-25-2016
The directions for mine say to oil at the end of each day's work or every 3 hours of run time. I put one drop of light oil in the air intake port, reconnected the hose, and ran it for ~3-5 seconds before putting it away. Don't know how this will work long-term, but it pretty much matches their instructions.