How to attach legs to my Uni's (ahem....FREE UNI!) extension table - Printable Version +- Woodnet Forums (https://www.forums.woodnet.net) +-- Thread: How to attach legs to my Uni's (ahem....FREE UNI!) extension table (/showthread.php?tid=7248919) |
How to attach legs to my Uni's (ahem....FREE UNI!) extension table - Dumb_Polack - 03-22-2016 Yes, Still gloating over the free UNI I acquired 2 months ago (Insert the obligatory "YOU SUCK" here, please...) Anywho, I built an extension table for it out of some counter tops I had laying around (I dunno where they came from and why I held on to them for so long but I did put them to good use). The 1st pic shows the extension in the dropped location. I set the hinge point back from the edge a few inches so I could still use the original extension to the right as an assembly table; I'm still able to use the edge to clamp something to it. Thought that was pretty clever of me, eh? [url=http://www.snapfish.com/library/photos?website=snapfish_us&cobrand=snapfish&locale=en_US#state=%7B"pgvw"%3A"siav"%2C"aid"%3A122769095550070%7D]http://www.snapfish.com/library/photos?w...769095550070%7D[/url] The 2nd pic shows the top up . Yes, it is a mishmash of countertop pieces, but it was all free and it works for me. [url=http://www.snapfish.com/library/photos?website=snapfish_us&cobrand=snapfish&locale=en_US#state=%7B"pgvw"%3A"siav"%2C"aid"%3A122769095550070%7D]http://www.snapfish.com/library/photos?w...769095550070%7D[/url] The 3rd pic shows one of the legs I have supporting the extension (you might be able to make out the 2nd leg in sitting on top of the saw in the 2nd picture. I can't hinge these legs so that they fold towards the saw as the extension isn't wide enough and they'd hit the saw. I was thinking about hinging them so that they fold in the direction of the drill press, but I would need to add a block so the outside one could bypass the inside one. Also I would want to lock them in position when they're in use and when they're folded down. I'm open to all suggestions (I also thought about having them drop down at a 45 degree angle and have a bird's mouth cut out to register them on the mobile base... anyone ever done that?) Re: How to attach legs to my Uni's (ahem....FREE UNI!) extension table - stav - 03-22-2016 Your pics are asking for a login to see them. Re: How to attach legs to my Uni's (ahem....FREE UNI!) extension table - Dumb_Polack - 03-22-2016 aw..crap!!! Lemme try and fix that. Re: How to attach legs to my Uni's (ahem....FREE UNI!) extension table - Jeremy s - 03-22-2016 ok i have to say it...you suck!! Are you going to get a Shark Guard for it? Re: How to attach legs to my Uni's (ahem....FREE UNI!) extension table - fredhargis - 03-22-2016 Dumb_Polack said: Hmmmm... here we go again Re: How to attach legs to my Uni's (ahem....FREE UNI!) extension table - Dumb_Polack - 03-22-2016 I dunno why they didn't post this time. I'll look at it manana Re: How to attach legs to my Uni's (ahem....FREE UNI!) extension table - K. L. McReynolds - 03-22-2016 You ain't fixt it yet. Re: How to attach legs to my Uni's (ahem....FREE UNI!) extension table - chips ahoy - 03-22-2016 so there is no extension table. Mel Re: How to attach legs to my Uni's (ahem....FREE UNI!) extension table - JGrout - 03-22-2016 chips ahoy said: But there is a concept Re: How to attach legs to my Uni's (ahem....FREE UNI!) extension table - chips ahoy - 03-22-2016 JGrout said: But there is a concept [/blockquote] Just a vision in his mind. Mel |