+- Woodnet Forums (https://forums.woodnet.net)
+-- Thread: Dividers, Calipers and Chisels (/showthread.php?tid=7322853)
Pages:
1
2
Dividers, Calipers and Chisels - johndi - 09-17-2016
Assorted calipers and dividers.
Would like $40.00 for all plus shipping.
Paypal F & F preferred.
Left to Right
Union dividers
Union large calipers
small unmarked calipers
B & S dividers marked "800"
Starrett inside calipers
Anthol Machine Co. calipers
![[Image: image.jpg1_zpsiwqgorkt.jpg]](http://s1298.photobucket.com/user/johndi1/media/image.jpg1_zpsiwqgorkt.jpg.html)
Chisels
No beauty queens, but should make good users. All need to be sharpened.
Note the 1/2 inch Everlast looks like it is developing a crack on the socket.
Would like $60.00 plus shipping for all.
Left to Right
NOS Great Neck 1/4 inch chisel
Stanley no. 60 1/2 inch with a hole drilled in handle
Everlast 1/2 inch
Everlast 1"
Everlast 3/4 "
Stanley no.40 1"
Stanley no. 40 1/2"
NOS Great Neck 2"
![[Image: image.jpg1_zpscs1neovz.jpg]](http://s1298.photobucket.com/user/johndi1/media/image.jpg1_zpscs1neovz.jpg.html)
RE: Dividers, Calipers and Chisels - johndi - 09-19-2016
I received a PM for calipers, but you have PM's disabled so I cannot reply.
RE: Dividers, Calipers and Chisels - glennw - 09-21-2016
If his request for them falls through I can I get them.
RE: Dividers, Calipers and Chisels - johndi - 09-21-2016
Glennw, if I don't hear anything in the next few days, I will PM you.
Not sure how they were able to send me a PM but can't get them?
RE: Dividers, Calipers and Chisels - iclark - 09-22-2016
(09-21-2016, 05:04 PM)johndi Wrote: Glennw, if I don't hear anything in the next few days, I will PM you.
Not sure how they were able to send me a PM but can't get them?
When WN switched to the new software. receiving PM's was turned off by default. This is the opposite of the old software.
Anyone can send a PM, but they can not receive them until they go into the UserCP and turn on receipt of PM's.
There was a thread from Arlin with very specific instructions of how to turn on receiving PM's.
So far, the admin in the attic seem to consider this PM setting to be a feature rather than an error.
RE: Dividers, Calipers and Chisels - glennw - 09-22-2016
praying I can for my luck
RE: Dividers, Calipers and Chisels - johndi - 09-24-2016
Glennw, tried to PM you.
You also have settings set not to receive PM's.
RE: Dividers, Calipers and Chisels - johndi - 09-28-2016
Both still available.
How about $40.00 for chisels to move them along.
RE: Dividers, Calipers and Chisels - glennw - 09-28-2016
if the calipers are still available I would like to get them. you can email me at gwiederman@icloud.com I am not sure how to set pm's so I can get them.
RE: Dividers, Calipers and Chisels - johndi - 09-29-2016
Consider calipers sold.
Glenn, I will email you today.