Woodnet Forums
FS: Drawknives, chisels, more added - Printable Version

+- Woodnet Forums (https://www.forums.woodnet.net)
+-- Thread: FS: Drawknives, chisels, more added (/showthread.php?tid=7325354)

Pages: 1 2 3

FS: Drawknives, chisels, more added - SteveF - 11-19-2016

Several nice drawknives.

There's a 6" Hart Mfg., a 7" C.J.Kimball, a 8" AST(Germany), and a 10" Greenlee. The only one I ground the edge on is the Kimball, all just need honing.  Tight handles on all, no problems.

6" $35
7" $30
8" $30
10" $35

[Image: 20161112_142223-L.jpg]
[Image: 20161112_142246-L.jpg]
[Image: 20161112_142302-L.jpg]
[Image: 20161112_142349-L.jpg]
[Image: 20161112_142140-L.jpg][Image: 20161112_142153-L.jpg]
[Image: 20161112_142406-L.jpg]
[Image: 20161112_142429-L.jpg]

RE: FS: Drawknives, chisels, marking gauge - SteveF - 11-19-2016

Handyman Club of America 7 piece chisel set. They look to be unused. The 1/4" edge is dinged up though, probably dropped.

$20 plus shipping

[Image: 20161117_164107-L.jpg]
[Image: 20161117_164121-L.jpg]
[Image: 20161117_164254-L.jpg]
[Image: 20161117_164326-L.jpg]

Marples 2033 marking gauge. This uses a wedged cutter.

$15 plus shipping

[Image: 20161119_131946-L.jpg]
[Image: 20161119_131955-L.jpg]
[Image: 20161119_132020-L.jpg]
[Image: 20161119_132031-L.jpg]

RE: FS: Drawknives, chisels, router, Stanley 10 - SteveF - 11-19-2016

Rockwell 6302 HD Motor with the 6301 base. Runs great, the bearings sound good. This has the 1/4" collet, the 1/2" is readily available (Porter Cable).

$50 plus shipping

[Image: 20161119_133346-L.jpg]
[Image: 20161119_133354-L.jpg]
[Image: 20161119_133404-L.jpg]
[Image: 20161119_133415-L.jpg]
[Image: 20161119_133424-L.jpg]
[Image: 20161119_133433-L.jpg]

RE: FS: Drawknives, chisels - SteveF - 11-19-2016

Stanley No.10 carriage plane. Nice old one with most of the original jappaning. I repaired the tote (broken in half). The iron is getting down to the end, but will probably last quite a bit longer. 

$85 plus shipping

[Image: 20161117_061039-L.jpg]
[Image: 20161117_061050-L.jpg]
[Image: 20161117_061102-L.jpg]
[Image: 20161117_061112-L.jpg]
[Image: 20161117_061139-L.jpg]
[Image: 20161117_061203-L.jpg]
[Image: 20161117_061228-L.jpg]

RE: FS: Drawknives, chisels - SteveF - 11-20-2016

The 6" Hart and 7" Kimball drawknives have been sold.

RE: FS: Drawknives, chisels - SteveF - 11-20-2016

4" drawknife. Unmarked, but it's in the Jennings style. I cleaned it up and ground a new edge, just needs honing. The handle tend to get loose on these. I reinstalled the handles and used JB Weld, they ain't coming off.

$30 plus shipping

[Image: 20161120_122338-L.jpg]
[Image: 20161120_122347-L.jpg]

Stanley 8" bevel.  It has nickle loss and a couple of spots of pitting, still way nicer than the one I use at work. Itlocks tightly, no problems.

$12 plus shipping

[Image: 20161120_122304-L.jpg]
[Image: 20161120_122316-L.jpg]

RE: FS: Drawknives, chisels - SteveF - 11-20-2016

Sandvik card scrapers. Unused, a few spots of corrosion. I have 2 of these.

$5 apiece plus shipping

[Image: 20161120_123326-L.jpg]
[Image: 20161120_123347-L.jpg]
[Image: 20161120_123438-L.jpg]
[Image: 20161120_123458-L.jpg]


North Bros. Stanley 433H spiral screwdriver. Works great, 3 bits.

$10 plus shipping

[Image: 20161120_123154-L.jpg]

RE: FS: Drawknives, chisels - Boatman53 - 11-20-2016

Steve, PM sent.
Jim

RE: FS: Drawknives, chisels - SteveF - 11-20-2016

Sold so far:

Hart Mfg. 6" drawknife

C.J.Kimball 7"drawknife

4" drawknife

Marples marking gauge

Both Sandvik scrapers

RE: FS: Drawknives, chisels - professore - 11-20-2016

PM on cutting gauge and scrapers.

Frank S in IA