+- Woodnet Forums (https://forums.woodnet.net)
+-- Thread: Boss wants a Pantry Cupboard (/showthread.php?tid=7330423)
Boss wants a Pantry Cupboard - bandit571 - 05-23-2017
Well, I had just gone through and resawn a few reclaimed 2x4s down....Boss comes up and says she wants a new pantry cupboard. had to go out and buy a bit of pine. 1x4s, 1x8s, and a couple 1 x 10s, all 6' long.
Glued up two panels to make the sides
[attachment=2343]
And ripped a 1x4 to make the stiles for a face frame
Had to crosscut a second 1 x 4
[attachment=2344]
Used the "new" panel saw for that. Needed two rails at 30" long. Join the rails to the stiles with half laps
[attachment=2345]
Needed to rip a few more parts, to make two webframes to help join the sides together..
[attachment=2346]
Had a benchful of tools to work on the laps..
[attachment=2347]
Just the usual suspects....
Stay tuned for the next episode....hope you like it.
RE: Boss wants a Pantry Cupboard - Stwood_ - 05-23-2017
I'm waiting for a popcorn refill.
RE: Boss wants a Pantry Cupboard - hbmcc - 05-23-2017
(05-23-2017, 05:35 PM)Stwood_ Wrote: I'm waiting for a popcorn refill.
Can I have carrots and broccoli?
There's wood. I have lots of that; and even for projects--some projects are forgotten.
Waiting......
Mmmmmm .....
Hhhhhuuuummmmmm .. oh hum....
RE: Boss wants a Pantry Cupboard - Stwood_ - 05-23-2017
Sure. Eat all your carrots.
Drumming fingers on desk.
Tap tap.....
RE: Boss wants a Pantry Cupboard - bandit571 - 05-23-2017
Will just have to wait until tomorrow evening, for the next episode...
til then...
[attachment=2355]
These USED to be a few 2 x 4s I salvaged. Resawn down to 3/4 x 3"
[attachment=2356]
The plain side..
[attachment=2357]
Saw mark side,,,
[attachment=2358]
Millers Falls #11 Junior Jack to smooth out both sides.
Will use these for parts for the cupboard build.
While you are waiting...
[attachment=2359]
The "other" kind of Dew should keep things interesting....
RE: Boss wants a Pantry Cupboard - Stwood_ - 05-24-2017
Oooh ok...............waiting till evening........
RE: Boss wants a Pantry Cupboard - bandit571 - 05-24-2017
Ok, this might take two posts....here goes ( until the glue dries...
)Cleaned all the saw marks up, made a LOT of shavings...
[attachment=2365]
The four shorter [ieces of the webframes needed tenons made
[attachment=2366]
Needed to set up a jig to chop a few mortises..
[attachment=2367]
Just three pieces of scrap. I can clamp each part in place...
[attachment=2368]
And do a mortise to match the tenon..
[attachment=2369]
Something like this. I chop into the far end, after a saw has made a kerf to follow. Pop the waste out.
Part 2...
RE: Boss wants a Pantry Cupboard - bandit571 - 05-24-2017
Part 2: Dry fits..
[attachment=2370]
Tenons seem to fit nicely, got all four corners done..
[attachment=2371]
And check for square..
[attachment=2372]
Looks decent. Went ahead and made both frames. Bottom webframe was glued up first..
[attachment=2373]
Not enough space ....
RE: Boss wants a Pantry Cupboard - bandit571 - 05-24-2017
For the rest of this morning's efforts....so, page three...
Top frame was a little different..
[attachment=2374]
Only one stiffener was used, as only the top is above it. Doesn't need to support a lot of can goods.
On both the sets of stiffeners, pilot holes were drilled. then a small drill was used
[attachment=2375]
With a countersink bit...
The single one was centered, the other two were set in about 5" from the outside edge. Drove one screw ( glue was applied first) and check for square, then drive the other screws.
So, Lunch Break! I have both webframes sitting all clamped up, once the glue has set, I can work on gluing up the face frame. Maybe tomorrow, I can attach the assemblies to the sides?
What's for Lunch?
RE: Boss wants a Pantry Cupboard - Stwood_ - 05-24-2017
Supper.......supper time......