Woodnet Forums
Face Shield works - Printable Version

+- Woodnet Forums (https://www.forums.woodnet.net)
+-- Thread: Face Shield works (/showthread.php?tid=7336371)

Pages: 1 2

Face Shield works - MidwestMan - 01-12-2018

I'm sure glad I was wearing the face shield, when this happened. I was putting the finishing touch on the outside of the bowl (slightest scrapping with just sharpened gouge) and in 1/10th of a blinking of an eye, the broken piece smacked me right in the face shield.

I knew there were a few hairline cracks... but I didn't think it would come apart.

[Image: SZbQbG.jpg]



But... I slapped on some CA glue... and I will gently sand it.

[Image: 7jYsIU.jpg]

RE: Face Shield works - MichaelMouse - 01-13-2018

(01-12-2018, 11:37 PM)MidwestMan Wrote: I'm sure glad I was wearing the face shield, when this happened. I was putting the finishing touch on the outside of the bowl (slightest scrapping with just sharpened gouge) and in 1/10th of a blinking of an eye, the broken piece smacked me right in the face shield.

I knew there were a few hairline cracks... but I didn't think it would come apart.

[Image: SZbQbG.jpg]

Took a pretty good dig with the scraper, judging by the photo.  One of the reasons why broad scraping presentations and endgrain don't mix.  

Once again, the wood looks ordinary, which means low tolerance for cracks.  If you knew they were there, you should have been reinforcing them all along, though nothing would keep you secure from a dig like the one in the picture.

One thing further - don't stand in the disintegration zone while turning.

RE: Face Shield works - Strokes77 - 01-13-2018

(01-13-2018, 06:39 AM)MichaelMouse Wrote: Took a pretty good dig with the scraper, judging by the photo.  One of the reasons why broad scraping presentations and endgrain don't mix.  

Once again, the wood looks ordinary, which means low tolerance for cracks.  If you knew they were there, you should have been reinforcing them all along, though nothing would keep you secure from a dig like the one in the picture.  

One thing further - don't stand in the disintegration zone while turning.

Thanks for sharing this.  New turners like me need to see stuff like this to keep us humble...

RE: Face Shield works - Woodshop - 01-13-2018

next time use wood glue.  CA is not the best bond for wood
I like the shape 
Yes oh nice lathe , I have a pm too

RE: Face Shield works - Dusty Workshop - 01-13-2018

I too agree that the bowl has a pleasing shape.

Is it finished yet?

RE: Face Shield works - MidwestMan - 01-13-2018

(01-13-2018, 06:39 AM)MichaelMouse Wrote: Took a pretty good dig with the scraper, judging by the photo.  One of the reasons why broad scraping presentations and endgrain don't mix.  

Once again, the wood looks ordinary, which means low tolerance for cracks.  If you knew they were there, you should have been reinforcing them all along, though nothing would keep you secure from a dig like the one in the picture.  

One thing further - don't stand in the disintegration zone while turning.

To be clearer... I only noticed a few slight cracks... that I DID put CA glue on. I thought I addressed the issue properly. ALSO, there was no "catch" at all with the "slight scraping". The wood broke apart from centrifical force mostly.

I didn't realize the slight cracks lined up to create a piece of the bowl.

RE: Face Shield works - MidwestMan - 01-13-2018

(01-13-2018, 10:44 AM)Woodshop Wrote: next time use wood glue.  CA is not the best bond for wood
I like the shape 
Yes oh nice lathe , I have a pm too

Your advise is right, I wish I had it earlier. I CA'd the piece back on and sanding down 320 grit. Alll was going well. Then I put on the shellac finish, and the piece broke off again. At that point, I had a shellac laden piece and in a hurried panic, I slapped on more CA and held it.

Then walked away. I haven't been in the shop since, so I don't know.

RE: Face Shield works - MidwestMan - 01-13-2018

(01-13-2018, 10:56 AM)Dusty Workshop Wrote: I too agree that the bowl has a pleasing shape.

Is it finished yet?

The previous message addresses the current status. Thanks for the compliment.

Soon, I'll go to the shop and decide if this is a bowl, or some fancy firewood.

RE: Face Shield works - Arlin Eastman - 01-13-2018

(01-13-2018, 06:39 AM)MichaelMouse Wrote: Took a pretty good dig with the scraper, judging by the photo.  One of the reasons why broad scraping presentations and endgrain don't mix.  

Once again, the wood looks ordinary, which means low tolerance for cracks.  If you knew they were there, you should have been reinforcing them all along, though nothing would keep you secure from a dig like the one in the picture.  

One thing further - don't stand in the disintegration zone while turning.

Midwest

Glad you were wearing the shield to.


MM

You have better eyes then mine since I do not see the dig in.

RE: Face Shield works - Arlin Eastman - 01-13-2018

(01-13-2018, 12:07 PM)MidwestMan Wrote: Your advise is right, I wish I had it earlier. I CA'd the piece back on and sanding down 320 grit. Alll was going well. Then I put on the shellac finish, and the piece broke half broke off again. At that point, I had a shellac laden piece and in a hurried panic, I slapped on more CA and held it.

Then walked away. I haven't been in the shop since, so I don't know.

Something to think about is shellac has Alcohol and it will affect the CA glue