+- Woodnet Forums (https://www.forums.woodnet.net)
+-- Thread: Daily Bench Shot (/showthread.php?tid=7336585)
Pages:
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
RE: Daily Bench Shot - Tankwood - 05-27-2021
(05-27-2021, 05:48 PM)Stwood_ Wrote: Odds and ends projects continue to hold the assembly table down.
Nice setup with enough room to play with the truck.
Sweet
RE: Daily Bench Shot - Gary G™ - 06-04-2021
(06-04-2021, 07:44 AM)daveginger Wrote: I am a spammer
RE: Daily Bench Shot - barnowl - 06-04-2021
(06-04-2021, 07:44 AM)daveginger Wrote: Could you tell the size plz? length height width
Spammer.
BAM!!!
RE: Daily Bench Shot - Stwood_ - 06-07-2021
(05-27-2021, 06:19 PM)Tankwood Wrote: Nice setup with enough room to play with the truck.
Sweet
Uhuh. I can get 4 of those in here with the tools and lumber. 5 actually, if I consider the addition.
RE: Daily Bench Shot - R Clark - 06-16-2021
Woodworking has slowed down a bit as major projects completed and the warmer weather meant it was time to do some fishing. I've been dabbling in carving some spoons, and decided I want a spoon mule to make it easier. Based on some YouTube vids, I kind of kluged some ideas and started half-a**ing a mule. Basic frame is first, and I'll start working on the seat and head tomorrow. Still need to trim the legs so I get the sitting height right and level it out.
[attachment=35905]
RE: Daily Bench Shot - Timberwolf - 06-17-2021
(06-16-2021, 04:03 PM)WxMan Wrote: Woodworking has slowed down a bit as major projects completed and the warmer weather meant it was time to do some fishing. I've been dabbling in carving some spoons, and decided I want a spoon mule to make it easier. Based on some YouTube vids, I kind of kluged some ideas and started half-a**ing a mule. Basic frame is first, and I'll start working on the seat and head tomorrow. Still need to trim the legs so I get the sitting height right and level it out.
........................
RE: Daily Bench Shot - Stwood_ - 06-17-2021
[attachment=35914]
RE: Daily Bench Shot - Belle City Woodworking - 06-21-2021
Still working on my Bench, but as Norm used to say....."We are gaining on it..."
I need to cut to final size, complete the base add the LN vise hardware and Bob's your Uncle
The bench top will be a full 4" thick sized at 7' long and 25" wide - LN Twin Screw face vise and LN Sliding tail vise.
The bench top alone weighs close to if not over 350 lbs. I should have built this when I was younger!
![[Image: IMG-0893.jpg]](https://i.postimg.cc/kXXRx7Cf/IMG-0893.jpg)
RE: Daily Bench Shot - R Clark - 06-21-2021
Well, here's the spoon mule as it currently sits. It's operational, though it can and will be changed as preferences change.
I'm trying a different approach with the seat. Most just have a "butt seat", and that's what I was going to do. Even glued up a blank to start hollowing and shaping. Them LOML asked, "Why don't you use the mower seat that's up in the loft?" Why not, indeed? It would save time and recycle an existing item back into use.
The mower seat may not work out. First, the arm rests are in the way when in the down position, and their steel supports are an integral part of the seat frame. If they're still in the way even when in the up position, the remedy is to cut them off with the angle grinder. I'll change it out if it just won't work. As it is, the only "waste" on that detour is a 14"x14" piece of scrap ply and an 8" piece of scrap 2X4.
The shave head is a kluge of ideas I saw on line. Like the rest, it can be changed as I use the setup.
The clamping mechanism holds tight.
[attachment=35978]
RE: Daily Bench Shot - R Clark - 06-21-2021
(06-21-2021, 09:57 AM)Belle City Woodworking Wrote: Still working on my Bench, but as Norm used to say....."We are gaining on it..."
I need to cut to final size, complete the base add the LN vise hardware and Bob's your Uncle
The bench top will be a full 4" thick sized at 7' long and 25" wide - LN Twin Screw face vise and LN Sliding tail vise.
The bench top alone weighs close to if not over 350 lbs. I should have built this when I was younger!
Wow.
I'm pretty certain the Government has a rule requiring special markings and lights to make sure airplanes won't try to land on that!
That's going to be an amazing bench.