+- Woodnet Forums (https://forums.woodnet.net)
+-- Thread: Daily Bench Shot (/showthread.php?tid=7336585)
Pages:
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
RE: Daily Bench Shot - cbygeorge - 01-30-2022
(01-29-2022, 09:23 AM)jstraw Wrote: Finished a Kumiko wall hanging. I try to learn something new for each project. This is a test panel for some sliding doors on a entertainment console project. Door panels with have speaker fabric backer instead of the walnut veneer on the test piece. Also will change up the design some.
John, that is really nice! I have seen some of that work being done on video. Couple questions please. Is that maple? Did you build a special jig/sled for making those cuts? Very impressive!
Thanks
Chuck
RE: Daily Bench Shot - jstraw - 01-31-2022
(01-30-2022, 06:03 PM)cbygeorge Wrote: John, that is really nice! I have seen some of that work being done on video. Couple questions please. Is that maple? Did you build a special jig/sled for making those cuts? Very impressive!
Thanks
Chuck
Thank you for your kind comments, appreciate it.
The wood used is basswood. It’s a good wood for this because the grain is not pronounced and the hardness is just right for a tight friction fit on the joints. The grid is glued at the half lap joints, but everything else is fit tight with no glue. Walnut also works well.
There are multiple jigs necessary. A small table saw sled with a fence that is similar to a box joint fence is made. Difference is that the pin for the box joint has multiple slots cut in equal increments that can be anywhere from 1/4” to 1/2”. That allows you to get the proper spacing for the half lap joints on the grid.
For the small squares, the pieces consist of half lap joints that form a hashtag pattern. Those are then mitered at a 45 on all 4 sides and requires another jig that screws to the base of the small table saw sled.
The large patterns are all mitered with a chisel on a special kumiko block that helps guide your chisel to the required 45, 60, and 30 degree miters. I enjoyed this hand tool process much more than the mitered hashtags on the table saw.
The frame is cherry scraps and the back panel is walnut veneer. Overall size is around 24”x15”.
If you want to explore this method, fine woodworking had a couple of articles and Matt Kenny wrote a nice book about it.
RE: Daily Bench Shot - cbygeorge - 01-31-2022
(01-31-2022, 11:01 AM)jstraw Wrote: Thank you for your kind comments, appreciate it.
The wood used is basswood. It’s a good wood for this because the grain is not pronounced and the hardness is just right for a tight friction fit on the joints. The grid is glued at the half lap joints, but everything else is fit tight with no glue. Walnut also works well.
There are multiple jigs necessary. A small table saw sled with a fence that is similar to a box joint fence is made. Difference is that the pin for the box joint has multiple slots cut in equal increments that can be anywhere from 1/4” to 1/2”. That allows you to get the proper spacing for the half lap joints on the grid.
For the small squares, the pieces consist of half lap joints that form a hashtag pattern. Those are then mitered at a 45 on all 4 sides and requires another jig that screws to the base of the small table saw sled.
The large patterns are all mitered with a chisel on a special kumiko block that helps guide your chisel to the required 45, 60, and 30 degree miters. I enjoyed this hand tool process much more than the mitered hashtags on the table saw.
The frame is cherry scraps and the back panel is walnut veneer. Overall size is around 24”x15”.
If you want to explore this method, fine woodworking had a couple of articles and Matt Kenny wrote a nice book about it.
Thanks John! Yes, I believe it was the article by Mike Farrington in FWW I was thinking of. He has some fine videos on this subject on youtube also. I appreciate your detailed response.
RE: Daily Bench Shot - ®smpr_fi_mac® - 02-01-2022
An urn for my daughter's guinea pig. I'll post a build thread when done.
RE: Daily Bench Shot - Aram - 03-20-2022
Finally mounted my new grinder, and used it for the first time. CBN, very nice.
![[Image: i-Sk9QTGv-M.jpg]](https://photos.smugmug.com/photos/i-Sk9QTGv/0/2b7f564e/M/i-Sk9QTGv-M.jpg)
RE: Daily Bench Shot - Stwood_ - 03-23-2022
Bump..............
RE: Daily Bench Shot - Aram - 03-26-2022
Two figured curly maple boards. Each will become two rectangles. I spent 4 hours marking. And thinking. A little off here or there and it cuts off something that needs to be there.
![[Image: i-7wmvg2N-M.jpg]](https://photos.smugmug.com/photos/i-7wmvg2N/0/5760d4d6/M/i-7wmvg2N-M.jpg)
RE: Daily Bench Shot - Tankwood - 03-27-2022
(02-01-2022, 10:52 PM)®smpr_fi_mac® Wrote: An urn for my daughter's guinea pig. I'll post a build thread when done.
Cool
RE: Daily Bench Shot - Aram - 03-27-2022
Pieces cut and shot to size. Rob Hanson shooting board and L-N low angle jack with a freshly honed edge. Not sure what the black sludge left by the side of the plane is.
![[Image: i-PvpVBw5-M.jpg]](https://photos.smugmug.com/photos/i-PvpVBw5/0/c24b8d5c/M/i-PvpVBw5-M.jpg)
RE: Daily Bench Shot - fishhh4 - 03-28-2022
[attachment=41406]
[attachment=41405]
Curly poplar...Hmmm
Daughter to do for Grandaughter first birthday party theme.
I guess cakes are old school. Cupcakes are yesterday.
Donuts are the thing.
[attachment=41407]