+- Woodnet Forums (https://www.forums.woodnet.net)
+-- Thread: Daily Bench Shot (/showthread.php?tid=7336585)
Pages:
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
RE: Daily Bench Shot - EdL - 01-30-2019
......................
RE: Daily Bench Shot - Redman - 01-30-2019
Steve, I see your shop helper has his back turned to the work.
EdL, did someone die leaving all those clothes behind?
RE: Daily Bench Shot - EdL - 01-30-2019
Have to rotate the hats / gloves with the cold temps and what I'm doing outside that I don't want to be doing.
Have carhats hung all over too.
Eda
RE: Daily Bench Shot - Redman - 01-31-2019
Livin' and learnin'. The few really cold days here I don't go out unless absolutely necessary.
RE: Daily Bench Shot - Belle City Woodworking - 01-31-2019
Working on the drawbore pegs for the 9' x 45" Farm Style Dining table I have been working on, this lumber is from a 150 year old dairy barn, this lumber is from the barn floor.
I will have them installed today and then some final sanding and finish.
![[Image: kil-TQDz-YRwu-VD97aal-Ac7w.jpg]](https://i.postimg.cc/Qxk9BDKM/kil-TQDz-YRwu-VD97aal-Ac7w.jpg)
![[Image: m-K7-JFl0x-Q-c-Bbg-IN56f7g.jpg]](https://i.postimg.cc/vHdxHTBj/m-K7-JFl0x-Q-c-Bbg-IN56f7g.jpg)
I will be glad to have this done so I can have my shop space back
John
RE: Daily Bench Shot - Redman - 01-31-2019
123456789
RE: Daily Bench Shot - Stwood_ - 01-31-2019
(01-31-2019, 09:48 AM)Redman Wrote:
123456789
+1 for John's table
RE: Daily Bench Shot - Gary G™ - 01-31-2019
+2
345678901234567
RE: Daily Bench Shot - Belle City Woodworking - 02-01-2019
Now, just some final sanding and then this piece is ready for the finishing room
![[Image: bo-CQhlkf-Rx-Ok-Nej-Nx8n-I8-Q.jpg]](https://i.postimg.cc/FK33xBTW/bo-CQhlkf-Rx-Ok-Nej-Nx8n-I8-Q.jpg)
I am beginning to see the light at the end of the tunnel. Due to my shoulder replacements I had to take it slow. I use to not like working like this, I liked to get the projects done and move on to the next one, but I have found this pace to be much more relaxing. Once this is done, I will get my shop and my Family Room (That is where the base for the table is) back!
RE: Daily Bench Shot - Rob Young - 02-01-2019
Polishing my...
Block plane blade! Was a bit bored and didn't really have a lot of time to do much in the shop last night. So pulled out the set of diamond paste syringes I got off eBay a few years ago and went to work on the back of a LN102 blade. LN finishes them off at somewhere around p400 grit equivalent which is in the neighborhood of 40 micron (um). The paste kit starts at 40um and ends at 0.5um. The cheaper green stropping crayons are around 5-10um. This is of course if you can believe the labels...
Just a dot of the paste is needed. I cut up strips of copier paper and they (usually) stick all by themselves to my granite plate. Then you work through the grits. When the paper changes color from the dye in the oil to nearly solid black, you are probably done with that grit.
Good way to kill 30 minutes or so. It goes very quickly.
[attachment=16202]
[attachment=16203]
[attachment=16204]