+- Woodnet Forums (https://forums.woodnet.net)
+-- Thread: Removing rust from old plane (/showthread.php?tid=7342602)
Pages:
1
2
Removing rust from old plane - overland - 09-20-2018
Is there some inexpensive solution I can buy or make to remove the rust from an old hand plane? I have just one that needs work, and I don't want to spend a lot.
RE: Removing rust from old plane - Blacky's Boy - 09-20-2018
(09-20-2018, 08:14 AM)overland Wrote: Is there some inexpensive solution I can buy or make to remove the rust from an old hand plane? I have just one that needs work, and I don't want to spend a lot.
One word, "Evaporust".
Cheap, effective and somewhat re-usable.
RE: Removing rust from old plane - DaveParkis - 09-20-2018
Evaporust is pretty good, but vinegar or Coke are cheaper. Evaporust will also discover the steel and you'll need to scrub it down with a Scotchbrite pad or steel wool to remove the staining. Personally, I use a coarse Scotchbrite pad and WD-40 from the start. Takes a little more elbow grease, but it's a LOT faster.
RE: Removing rust from old plane - Timberwolf - 09-20-2018
(09-20-2018, 09:07 AM)DaveParkis Wrote: Evaporust is pretty good, but vinegar or Coke are cheaper. Evaporust will also discover the steel and you'll need to scrub it down with a Scotchbrite pad or steel wool to remove the staining. Personally, I use a coarse Scotchbrite pad and WD-40 from the start. Takes a little more elbow grease, but it's a LOT faster.
,,,,,,,,,,,,,,,,,,,,,,,,,
Yep...Vinegar works fine and is by far the cheapest way to go...About two bucks a gallon.
RE: Removing rust from old plane - rwe2156 - 09-20-2018
No question Evaporust is far superior to vinegar.
Be sure to wire brush as much rust off as you can before soaking.
RE: Removing rust from old plane - bandit571 - 09-20-2018
And...have a can of WD40 handy when you remove the parts from the dip tank......
Dungeon Rehab shop does not use any soakings, to clean up a planes....maybe a spritz of WD40 to keep the rust bunnies away....to be followed up with a cheap paint brush soaked in 3in1 oil. From this..
[attachment=13252]
To this...
[attachment=13253]
Walked home with this Dunlap #3 one afternoon..by bedtime it was done.
RE: Removing rust from old plane - AHill - 09-20-2018
Three ways to remove rust. The most effective is chelation (Evapo-Rust). It's also the most expensive.
Mechanical Abrasion:
WD-40 and a Scotchbrite pad or sandpaper
Wire brush (powered or hand-held)
Razor blade (flat surfaces)
Acid Etching:
Removes rust by attacking the layer of unrusted metal underneath the rust. Rust flakes off.
Acetic Acid (Vinegar)
Citric Acid (Pretty much the same as Acetic - food preservatives)
Phosphoric Acid (Sodas, TSP - Tri-sodium-phosphate)
Hydrochloric Acid (Rustoleum)
Oxalic Acid
Chelation:
Removes rust by chemical reaction pulling the rust into a liquid solution of other chemicals - unrusted metal is intact.
Evaporust
RE: Removing rust from old plane - Timberwolf - 09-20-2018
(09-20-2018, 10:50 AM)bandit571 Wrote: And...have a can of WD40 handy when you remove the parts from the dip tank......
Dungeon Rehab shop does not use any soakings, to clean up a planes....maybe a spritz of WD40 to keep the rust bunnies away....to be followed up with a cheap paint brush soaked in 3in1 oil. From this..
To this...
Walked home with this Dunlap #3 one afternoon..by bedtime it was done.
,,,,,,,,,,,,,,,,
After cleaning tools, I use a deburring wheel...bought one about 15yrs ago and have never looked back...They can put the finishing touch on any rusted or patinated tool in short order....I let electrons do the heavy lifting.
RE: Removing rust from old plane - Admiral - 09-20-2018
(09-20-2018, 11:30 AM)AHill Wrote: Mechanical Abrasion:
WD-40 and a Scotchbrite pad or sandpaper
Wire brush (powered or hand-held)
Razor blade (flat surfaces)
I'd reverse this order, I use a razor blade first.
RE: Removing rust from old plane - Bibliophile 13 - 09-20-2018
First time I used it, I was shocked at how much rust a razor blade removed. Seriously, try it. Follow up with some WD40 and sandpaper on the parts a blade can’t reach.
A wire wheel on a grinder or drill press can help, too, especially on screw threads after soaking in acid (vinegar, etc). Just hold on tight!