Benchtop Tablesaw Recomendation - Printable Version +- Woodnet Forums (https://www.forums.woodnet.net) +-- Thread: Benchtop Tablesaw Recomendation (/showthread.php?tid=7346631) |
Benchtop Tablesaw Recomendation - Mike 55 - 02-23-2019 Hi, I'm in need of a benchtop tablesaw to use in my garage. I now live in a 55+ community with a full shop. There are times I don't want to drive up just to rip one board. Plus, it's not open every day. I always buy the best possible so I'm not looking for a cheap piece of junk. It needs to make finished quality cuts. Thanks Mike RE: Benchtop Tablesaw Recomendation - Tapper - 02-23-2019 (02-23-2019, 11:02 AM)Mike 55 Wrote: Hi, Don't have a benchtop saw, but here's a start. Doug RE: Benchtop Tablesaw Recomendation - Woodenfish - 02-23-2019 Skip the portable bench top saws and acquire a track saw. Lighter weight, easier to move, transport and store. I find mine extremely accurate, has better dust control and is safer to operate. Best thing is that I don’t need any special jigs, miter gauges, and a host of safety items that I may or may not use as required. RE: Benchtop Tablesaw Recomendation - museumguy - 02-23-2019 I never thought that I would like this one but it's what my employer bought for me. Now that I've used it for a few months, I like it. https://www.lowes.com/pd/dewalt-10-in-carbide-tipped-blade-15-amp-portable-table-saw/50056271?cm_mmc=shp-_-c-_-prd-_-tah-_-google-_-lia-_-129-_-miterandtablesaws-_-50056271-_-0&kpid&store_code=719&k_clickID=go_625706834_34613745310_111132553510_pla-261169297348_c_9007691&gclid=Cj0KCQiA-8PjBRCWARIsADc18TL7s90GgV-xNXZ5W9vNaL_Ljt8RltKRiQbguTWxFvB_AhOSyr7TOZMaAkBmEALw_wcB I really like the new gear drive to raise and lower the blade, nice improvement. RE: Benchtop Tablesaw Recomendation - messmaker - 02-24-2019 I would take a hard look at the Ridgid. RE: Benchtop Tablesaw Recomendation - museumguy - 02-24-2019 (02-24-2019, 09:51 AM)messmaker Wrote: I would take a hard look at the Ridgid. I have an older Ridgid contractor saw, love it. I had a Ridgid jobsite saw, hated it for one reason only. The throat plate was just a piece of sheet steel. Due to the design, I never could make a ZCI, maybe I didn't think it through. I still prefer the Dewalt, just my opinion. RE: Benchtop Tablesaw Recomendation - Cian - 02-24-2019 (02-24-2019, 09:51 AM)messmaker Wrote: I would take a hard look at the Ridgid. This. I don't use it often, but I'm always impressed by my portable Ridgid. The equivalent Bosch is also very good. They've even improved a few things since I bought mine like a riving knife. RE: Benchtop Tablesaw Recomendation - EvilTwin - 02-24-2019 (02-24-2019, 04:40 PM)Cian Wrote: This. I don't use it often, but I'm always impressed by my portable Ridgid. The equivalent Bosch is also very good. They've even improved a few things since I bought mine like a riving knife. I had a very large saw, a Delta 12/14 and sold it a few months ago and picked up a Bosch 4100-09 with the gravity rise stand. Its the slightly earlier model and has a few more metal parts instead of plastic. I haven't used it much since I got it late in the year, but the few cuts I made were very clean and square. I got it for about 100 off the store price, since it was old stock and I got a military discount to boot. I could have gotten the Ridgid or the Hitachi for about a hundred or so less. They are also nice saws but I liked the fence on the Bosch better. This is the best review I found when I was looking: RE: Benchtop Tablesaw Recomendation - bpatters69 - 02-25-2019 (02-23-2019, 11:02 AM)Mike 55 Wrote: Hi, My first table saw was the Dewalt benchtop. It had enough power to do what I wanted and it was square and accurate. It could also take a Dado blade. The rack and pinion fence was pretty cool too. I have never used the Bosch but in support of Bosch, they are one of my favorite companies so I bet their saw is a solid choice too. RE: Benchtop Tablesaw Recomendation - lilrichard2 - 02-25-2019 (02-23-2019, 11:02 AM)Mike 55 Wrote: Hi, Mike, I posed a similar request here about a year ago, and though I have a Festool track saw, I needed a table saw for small pieces that were repeatable. I received a number of suggestions including Rigid, DeWalt, and others, but I settled on the Bosch job-site saw because it had a fold-up capability and took up minimum m floor space when not needed. It has met all my expectations. BTW, I moved from a basement shop in Ohio to a garage shop in the Florida panhandle. r2 |