+- Woodnet Forums (https://forums.woodnet.net)
+-- Thread: ?? About nail gun for hardie trim siding (/showthread.php?tid=7350116)
Pages:
1
2
?? About nail gun for hardie trim siding - Randy C - 09-05-2019
Does anyone know if it takes any special pneumatic nailer to nail HArdie trim boards. Specifically I will be nailing the 3/4 in thick hardie trim and this stuff is very hard.
would you use 15 or 16 gauge nailer. I can buy either nailer on Amazon but didn't know if these would have the power to nail thru this material.
Thanks
RE: ?? About nail gun for hardie trim siding - Snipe Hunter - 09-05-2019
I know Hardie recommends Hot Dipped Galvanized (not Galv Plated) or Stainless nails. Not sure you can get Hot Dipped for a nail gun so it would have to be stainless nails.
Look at Page 2
RE: ?? About nail gun for hardie trim siding - CLETUS - 09-05-2019
They have specific installation instructions.
https://www.jameshardiepros.com/getattachment/513223b4-054b-4112-ab6b-38974c62c9cb/hardieplank-hz5-us-en.pdf
RE: ?? About nail gun for hardie trim siding - Randy C - 09-05-2019
(09-05-2019, 03:08 PM)CLETUS Wrote: They have specific installation instructions.
https://www.jameshardiepros.com/getattachment/513223b4-054b-4112-ab6b-38974c62c9cb/hardieplank-hz5-us-en.pdf
Thanks, but I know all this. I am trying to find out if a regular 15 or 16 gauge nail gun will have the power to nail thru this hard material or does it take some specialized gun or an air compressor that goes above 120 psi.
RE: ?? About nail gun for hardie trim siding - Stwood_ - 09-05-2019
Doubtful on the 16-15ga finish nailer. Son uses a Dewalt siding coil nailer.
https://www.dewalt.com/products/power-tools/nailers-and-staplers/specialty-nailers/15-coil-siding-and-fencing-nailer/dw66c-1
RE: ?? About nail gun for hardie trim siding - Admiral - 09-05-2019
(09-05-2019, 04:19 PM)Randy C Wrote: Thanks, but I know all this. I am trying to find out if a regular 15 or 16 gauge nail gun will have the power to nail thru this hard material or does it take some specialized gun or an air compressor that goes above 120 psi.
Think a "siding nailer" is what you want, which I think is in between a framing nailer and finish nailers. Pros would know more.
RE: ?? About nail gun for hardie trim siding - cams2705 - 09-05-2019
I just installed Hardie Panel siding on my shed two weeks ago. I used just what it said on the data sheet. 6d galvanized. I hand nailed and thought it would be a hassle, but it wasn't bad at all. A good whack with the hammer and the nail went right through and hammer them flush with the surface. Pay close attention to the recommended offset from the edges for nail placement as there was one spot where I got a little close and it cracked a little on a corner.
RE: ?? About nail gun for hardie trim siding - mike4244 - 09-06-2019
You can hand nail the trim with stainless steel siding nails. No problem nailing thru the Hardie Board. If the nails won't show then a roofing nailer will work too.
RE: ?? About nail gun for hardie trim siding - vernonator - 09-06-2019
They have a Facebook page and are fairly responsive to posts - could just ask them.
RE: ?? About nail gun for hardie trim siding - CLETUS - 09-06-2019
(09-05-2019, 04:19 PM)Randy C Wrote: Thanks, but I know all this. I am trying to find out if a regular 15 or 16 gauge nail gun will have the power to nail thru this hard material or does it take some specialized gun or an air compressor that goes above 120 psi.
Ok, I figured if you knew all of that you'd go this route as suggested.
• Siding nail (0.09 in. shank x 0.221 in. HD x 2 in. long)
• 11ga. roofing nail (0.121 in. shank x 0.371 in. HD x 1.25 in. long) Screws - Steel Framing • Ribbed Wafer-head or equivalent (No. 8 x 1 1/4 in. long x 0.375 in. HD)
• ET & F Panelfast® nails or equivalent (0.10 in. shank x 0.313 in. HD x 1-1/2 in. long) Nails must penetrate minimum 1/4 in. into metal framing. OSB minimum 7/16 in.
• 11ga. roofing nail (0.121 in. shank x 0.371 in. HD x 1.75 in. long)
• Ribbed Wafer-head or equivalent (No. 8 x 1 5/8 in. long x 0.375 in. HD).