Tablesaw Blade Choice - Printable Version +- Woodnet Forums (https://www.forums.woodnet.net) +-- Thread: Tablesaw Blade Choice (/showthread.php?tid=7352043) |
Tablesaw Blade Choice - Tapper - 12-27-2019 Time to buy a new tablesaw blade for my 3 HP cabinet saw. Looking for general purpose for both ripping and crosscutting. I know that Forest Woodworker is probably top-of-the-heap but I'm not sure I want to spend that much. Just read a couple of reviews on the Freud Diablo which were positive. It's a combo blade, thin kerf. Haven't used a thin kerf blade in quite a while. Recommendations from personal experience would be appreciated. Thanks, Doug RE: Tablesaw Blade Choice - Derek Cohen - 12-27-2019 Doug, I guess it will come down to what you want to spend. I have dedicated rip and crosscut blades by Leitz, and prefer to use a combination blade from Leuco. The performance of all is top notch, but the prices are as well. .. on a train to Prague Derek RE: Tablesaw Blade Choice - R Clark - 12-27-2019 Freud is my go-to brand for tablesaw blades. I usually keep a 50-tooth thin-kerf combo blade installed most of the time, only changing out for dado operations (a Freud SD508) or a significant instance of ripping (Freud's 30-tooth Glue line rip blade). I'm not hesitant at all to use that combo blade for ripping operations and it does a nice crosscut. The kerf on my big sled is sized for that thin kerf blade. I (very briefly) considered getting a Forrest Woodworker II, but I don't think I'll ever see the benefit from spending over twice as much for a blade. I find that the Freud blades sharpen and hold edges pretty well. And if I lose one to an "oops" on my Sawstop, as has happened once over the past eight years, then I'm not out a great deal of money for a replacement. As for the Diablo versus their standard line, I can't really talk to that. I don't know the real difference there. RE: Tablesaw Blade Choice - Gary G™ - 12-27-2019 Stehle—if you can locate a reseller. https://www.stehle-int.com/static/stehle/en/saw-blades/html5/index.html?&locale=ENG RE: Tablesaw Blade Choice - shoottmx - 12-27-2019 Doug, I have a Freud LU84R011 50t full kerf combo and a WWll sharpened by Forrest that I use on my SS. I think the Freud gives a cleaner cut than the WWll for a little over half the $. It is my go to for clean cuts. Full kerf blades make math easier (IMHO) when figuring the cut width in multiple cuts. g RE: Tablesaw Blade Choice - fredhargis - 12-27-2019 I wouldn't suggest a thin kerf for your saw, but if you insist make sure the splitter or riving knife will work with a TK. RE: Tablesaw Blade Choice - R Clark - 12-27-2019 The riving knife on my SS is not really sized for a thin kerf blade. It works, but at its thickest point, the RK is slightly thicker than the thin kerf blade. RE: Tablesaw Blade Choice - Philip1231 - 12-27-2019 Hard to beat the Freud Fusion: its on my saw 99% of the time. RE: Tablesaw Blade Choice - Bill Lyman - 12-27-2019 I agree with Philip 1231, It is hard to beat the Freud Fusion as a general purpose table saw blade. Any time I have a series of rips and cross cuts, it is my go to blade. Otherwise, I like Freud blades, rip, cross cut and plywood and melamine. RE: Tablesaw Blade Choice - SteveS - 12-27-2019 I have a few different blades for my saw; I have a Forrest WWII standard kerf blade, a 50T freud crosscut and 24T Freud glue line rip. They all are excellent blades. The WWII is on the saw most of the time. I also wouldn't recommend a thin kerf. For me they are not stiff enough for thick or dense woods like African blackwood. |