+- Woodnet Forums (https://www.forums.woodnet.net)
+-- Thread: How do you sharpen a 1/8 or 3/16 bandsaw blade? (/showthread.php?tid=7352622)
How do you sharpen a 1/8 or 3/16 bandsaw blade? - stoppy - 01-27-2020
On my wider blades I sharpen them on the machine using the Dremel with a cylindrical stone. How do you sharpen the real narrow blades with the higher TPI? Just touch up the point?
RE: How do you sharpen a 1/8 or 3/16 bandsaw blade? - Timberwolf - 01-27-2020
(01-27-2020, 10:53 PM)stoppy Wrote: On my wider blades I sharpen them on the machine using the Dremel with a cylindrical stone. How do you sharpen the real narrow blades with the higher TPI? Just touch up the point?
.........................
Needle files, Jim...just the points
RE: How do you sharpen a 1/8 or 3/16 bandsaw blade? - stoppy - 01-27-2020
(01-27-2020, 10:59 PM)Timberwolf Wrote: .........................
Needle files, Jim...just the points
Jack,
On or off the machine?
RE: How do you sharpen a 1/8 or 3/16 bandsaw blade? - Timberwolf - 01-27-2020
(01-27-2020, 11:05 PM)stoppy Wrote: Jack,
On or off the machine?
......
Jim, I would try it on the machine..Make sure you have enough tension on the blade. Raise the guide all the way up...You may find that the blade will " chatter".. AKA "vibrate" somewhat but you can "back up the blade" with the other hand as you file, to reduce that tendency..Try to use the same number of strokes on each tooth, and file just until you have removed the shiny spot on the tip of each dull point..A three sq file would be my first choice but a small "half round" file could probably work since you will be just retouching the tips...A cheap Chinese diamond file may also work. If you have mastered using the Dremel method, you should have no trouble using the file..
EDIT...You can buy a three sq. India stone and that should work fine if you intend to keep making toys..They may cost more than cheap needle files but will last much longer and probable do a nicer job...I have several in my tool chest and they are also available in Arkansas three sq. hones.
RE: How do you sharpen a 1/8 or 3/16 bandsaw blade? - stoppy - 01-28-2020
I intend on making the toys. Like the idea of doing it on the machine. What about diamond paddles like I use on the Forstner bits?
RE: How do you sharpen a 1/8 or 3/16 bandsaw blade? - mike4244 - 01-28-2020
(01-27-2020, 10:53 PM)stoppy Wrote: On my wider blades I sharpen them on the machine using the Dremel with a cylindrical stone. How do you sharpen the real narrow blades with the higher TPI? Just touch up the point?
I have sharpened quite a few band saw blades but none that have more than 3 TPI. I also use a Dremel and the chain saw stones. Personally I would throw out small blades rather then try to sharpen them. If you use a lot of 3/16" blades, buy coil stock and hard solder them.
I did this with 1-1/2 TPI and 3TPI blades for my 16" band saw. I get 7 blades out of each 100'-0" coil. Quite a savings over separate blades.
mike
RE: How do you sharpen a 1/8 or 3/16 bandsaw blade? - Derek Cohen - 01-28-2020
I have sharpened more bandsaw blades than I can remember, and would do none of the above.
I use a Dremel with a small diamond disk (cheap on eBay) to literally "touch" the back of the tooth - never the gullet! All tou are doing is removing the wear bevel.
The blade remains on the bandsaw, turn to each tooth, keep the angle constant ...
![[Image: Bandsaw-sharpening-zpshsfsnsi9.jpg]](https://i.postimg.cc/cHppC10K/Bandsaw-sharpening-zpshsfsnsi9.jpg)
There are several videos on YouTube.
Here's the method used with a jig (I do it freehand) ..
Regards from Perth
Derek
RE: How do you sharpen a 1/8 or 3/16 bandsaw blade? - Timberwolf - 01-28-2020
(01-28-2020, 01:18 AM)stoppy Wrote: I intend on making the toys. Like the idea of doing it on the machine. What about diamond paddles like I use on the Forstner bits?
.........................
They will work also if they will fit between the teeth...a 1/8" blade is going to have very fine teeth so using a disc and a Dremel may not be able to do the job because of the thickness of the disc. You can ruin the small blade instantly if you make the slightest mistake with a power tool..Whatever method you use is going to be tedious because of the size and the number of teeth. I don't know how good your sight is but I have to wear an Opti-Visor when I have to do close work like that...I really don't think I would have the patience to sharpen a small fine-tooth blade like that anymore...but more power to you if you do....
RE: How do you sharpen a 1/8 or 3/16 bandsaw blade? - stoppy - 01-28-2020
I have the Dremel and the disks. Will check to see if it will work on the 1/8 inch blade.
RE: How do you sharpen a 1/8 or 3/16 bandsaw blade? - Arlin Eastman - 01-28-2020
I bought this and sharpen all my blades with them and carve in some river rock with them to and they do very well.
Started with these
https://www.ebay.com/itm/30Pcs-Diamond-Burr-Bits-Drill-Kit-Engraving-Carving-Dremel-Rotary-Replace-Tool/223302583809?epid=1379686210&hash=item33fddf0601:g:mP4AAOSw87JcJDcq
Now I buy 3 at a time