+- Woodnet Forums (https://www.forums.woodnet.net)
+-- Thread: new lathe decision (/showthread.php?tid=7354470)
Pages:
1
2
new lathe decision - joezjr - 04-11-2020
laguna revo 18/36 or nova galaxy---tks,joe
RE: new lathe decision - Arlin Eastman - 04-11-2020
(04-11-2020, 07:34 PM)joezjr Wrote: laguna revo 18/36 or nova galaxy---tks,joe
What is your budget??
Do you have any funds for other turning equipment as well?
RE: new lathe decision - Tim J. Chase - 04-11-2020
(04-11-2020, 07:34 PM)joezjr Wrote: laguna revo 18/36 or nova galaxy---tks,joeI would recommend the Nova just from personal experience, my DVR 3000 is around 15 years old and no problems no vibration my beltless beauty. I would just be torn over the swing. I will tell you past 15 " diameter bowls are pretty but to big for normal people ask around people will tell you. I say Nova.
RE: new lathe decision - gear jammer - 04-12-2020
I have a grizzly 838. I can go up to 28 inch bowls. Haven't even come close to that. Usually 12 inch for my largest. Happier at 8 to 10 inch. brother in law has a 18/36 Laguna and loves it. I have been on it and it is a good machine. Between the two of us we put it through it's paces and it did nicely.
RE: new lathe decision - Arlin Eastman - 04-12-2020
One thing I really like about my pm3520b is the movable headstock. I can move it all the way to the end and turn a 38" round table top which I want to do soon or two of them.
See if either one can turn outboard of movable headstock and you will have your answer of turning small or large and by large it does not have to be a bowl.
RE: new lathe decision - Wipedout - 04-12-2020
(04-12-2020, 12:46 PM)Arlin Eastman Wrote: One thing I really like about my pm3520b is the movable headstock. I can move it all the way to the end and turn a 38" round table top which I want to do soon or two of them.
See if either one can turn outboard of movable headstock and you will have your answer of turning small or large and by large it does not have to be a bowl.
We'll both have moving headstocks I've heard good things about the Laguna. Some well known Turner recently started using one and had a few videos on it. I just can't remember who
RE: new lathe decision - AnthonyYak - 04-12-2020
(04-12-2020, 03:40 PM)Wipedout Wrote: We'll both have moving headstocks I've heard good things about the Laguna. Some well known Turner recently started using one and had a few videos on it. I just can't remember who
I own one
RE: new lathe decision - Wipedout - 04-13-2020
(04-12-2020, 08:55 PM)AnthonyYak Wrote: I own one
There you go - he's the one
You going chime in and give the OP your thoughts?
RE: new lathe decision - SteveS - 04-13-2020
Whichever one isn't made in China.
RE: new lathe decision - sniper - 04-15-2020
(04-13-2020, 08:48 AM)SteveS Wrote: Whichever one isn't made in China.
That would be Robust.
Looking at both of them, personally I don't think I would like the membrane type control pad on the Nova. I don't care how tough it is when it's new, over the buttons is going to crack and chip with time. The nerd in me likes the controls, but the practical side of me thinks the Laguna controls will be better over time.
My argument against the Laguna is the extremely lousy customer service I've heard about for the entire 16+ years I've been on WN. Unless they've done a 180 recently, I'd be leery of them. IF they have improved their CS, then with only looking at the specs and demo videos, I'd go with Laguna. I've always been impressed with the quality of their tools, but the lack of CS has kept me from owning anything from them.
BTW, for reference, I've got an American Beauty, so my views may be skewed a little.