+- Woodnet Forums (https://forums.woodnet.net)
+-- Thread: Purchased my Clear Vue......now a question (/showthread.php?tid=7359778)
Purchased my Clear Vue......now a question - Wayne G. - 12-29-2020
I finally purchased my clear vue DC. I purchased the the CV1800 w/ upgraded fan. I drug my feet on this simply because I have to completely redesign my shops DC so that my CNC will get good DC. Anyhow, one simple question. I thought I remembered reading that these units need at least a 5' run before bends or drops in order to create optimal velocity inside the pipe. Is this correct? I ask because I've seen set-ups where people introduce 45's almost immediately before running their trunk. I coud inastall this unit to my current piping however the trunk line would run 8' then do a 180 back to my CNC and I'm wondering how well that would really work
RE: Purchased my Clear Vue......now a question - fredhargis - 12-29-2020
I have the CV1800 with the larger impeller as well. You understand it correctly, but in a home shop sometimes what's perfect isn't possible. One thing to remember, the CV 1800 will pull so much air that it's more likely to be restricted by whatever you have for a pick up at the CNC than it will be by the elbows. I most certainly wouldn't run it another 8' and then 180 back to the CNC.
RE: Purchased my Clear Vue......now a question - Wayne G. - 12-29-2020
(12-29-2020, 12:27 PM)fredhargis Wrote: My thoughts as well. I have been told I overthink things though. LOL
I have the CV1800 with the larger impeller as well. You understand it correctly, but in a home shop sometimes what's perfect isn't possible. One thing to remember, the CV 1800 will pull so much air that it's more likely to be restricted by whatever you have for a pick up at the CNC than it will be by the elbows. I most certainly wouldn't run it another 8' and then 180 back to the CNC.
RE: Purchased my Clear Vue......now a question - TDKPE - 12-29-2020
That's a fine tuning detail. You're hitting that gnat with a 12 lb sledge hammer. Use it as you originally wanted to, and don't worry about the details, as fredhargis suggested.
IMO, of course.
RE: Purchased my Clear Vue......now a question - mdhills - 12-29-2020
I thought the desire with the straight run was to improve separation efficiency on the cyclone rather than maximizing air flow.
Matt
RE: Purchased my Clear Vue......now a question - Wayne G. - 01-02-2021
(12-29-2020, 10:31 PM)mdhills Wrote: I thought the desire with the straight run was to improve separation efficiency on the cyclone rather than maximizing air flow.
Matt
Hmmmm, I should look into that before it arrives. I think I can get a 5 foot or greater run but would be nice to have it planned ahead of it arriving.
RE: Purchased my Clear Vue......now a question - fredhargis - 01-02-2021
It is, but that's only the section leading into the cyclone. Oneida wanted 5' (maybe it was 7', don't remember) but the smooth air flow (a laminar flow I think it's called). does indeed maximize separation. But a smooth flow along the whole line of ducting also improves flow. I'm pretty sure that it's an amount you could only measure in a lab (the fine tuning thing Tom mentioned)....but it's a truth. That's why many of us use 2-45º els with a short piece of pipe in between them instead of the sharp 90s that PVC usually has. On mine the best I could do on the inlet was a piece of straight about 15" long. One thing you need to consider is the CV has an upward angle to the inlet (about 10º according my HF angle thingy) so you have to consider ceiling height to get the straight infeed. I can tell you the separation is still very good on mine even with the short infeed tube I used.