+- Woodnet Forums (https://forums.woodnet.net)
+-- Thread: How do you cut the fascia for this stair stringer? (/showthread.php?tid=7371158)
Pages:
1
2
How do you cut the fascia for this stair stringer? - Dumb_Polack - 10-31-2022
Fellas?
Building a deck for my BIL and we're almost to the point where we're going to apply the "fascia" around the joists/stringers. Now, I realize I should have applied the stair fascia on before the railing and treads went on, but that's water under the bridge at this point.
Short of taping on pieces of heavy paper/cardboard and then tracing it on the fascia material, how would you go about cutting the piece to cover the stair stringer? thanks!
RE: How do you cut the fascia for this stair stringer? - joe1086 - 10-31-2022
Hmm...how are the stair stringers attached to the header? Looks like they are just hanging...
RE: How do you cut the fascia for this stair stringer? - Dumb_Polack - 10-31-2022
(10-31-2022, 07:44 AM)joe1086 Wrote: Hmm...how are the stair stringers attached to the header? Looks like they are just hanging...
There are 6 stair stringer straps holding them up
RE: How do you cut the fascia for this stair stringer? - joe1086 - 10-31-2022
There should be more header/structure behind the top step. Like the pic below. If it were me first thing to do is fix/add the header structure. Doesn't look like there's room to add facia to the risers...is that the plan?
RE: How do you cut the fascia for this stair stringer? - Snipe Hunter - 10-31-2022
Usually you cut the treads flush with the outside stringers and and run the fascia straight. The only cuts are at the top and the bottom. If you don't want to have a straight fascia, you cut the stringers and the fascia "stacked" at the same time.
RE: How do you cut the fascia for this stair stringer? - Snipe Hunter - 10-31-2022
(10-31-2022, 08:41 AM)Dumb_Polack Wrote: There are 6 stair stringer straps holding them up
That would make me nervous. I'd add a couple posts if I were doing it that way. Note the notch at the top of the post.
![[Image: wPr4n0H.jpg]](https://i.imgur.com/wPr4n0H.jpg)
RE: How do you cut the fascia for this stair stringer? - Roly - 10-31-2022
(10-31-2022, 09:16 AM)Snipe Hunter Wrote: That would make me nervous.
That was my first thought also. Roly
RE: How do you cut the fascia for this stair stringer? - Snipe Hunter - 10-31-2022
I'd also block in those risers... at least make an attempt to meet code.
RE: How do you cut the fascia for this stair stringer? - Dumb_Polack - 11-01-2022
(10-31-2022, 05:45 PM)Snipe Hunter Wrote: I'd also block in those risers... at least make an attempt to meet code.
The risers are blocked. IIRC, since there are 4 risers and 9 steps, I put in 18 bocks.
RE: How do you cut the fascia for this stair stringer? - joe1086 - 11-01-2022
(11-01-2022, 08:03 AM)Dumb_Polack Wrote: The risers are blocked. IIRC, since there are 4 risers and 9 steps, I put in 18 bocks.
Stairs over 30" (36"?) are supposed to have closed risers. The first two steps in the pic show open risers.