![]() |
New Harbor Freight 14” Bandsaw in search of blades - Printable Version +- Woodnet Forums (https://forums.woodnet.net) +-- Thread: New Harbor Freight 14” Bandsaw in search of blades (/showthread.php?tid=7374641) Pages:
1
2
|
New Harbor Freight 14” Bandsaw in search of blades - Johnny Currado - 12-31-2023 I just purchased a brand new harbor freight 14” four speed floor band saw and I am looking for some suggestions on what blades to look for to purchase. Blade size on this unit per the instructions are 93-1/2” long x 3/8”w x 0.02” T. What should I be looking for when I am purchasing some new blades for this new bandsaw? RE: New Harbor Freight 14” Bandsaw in search of blades - tablesawtom - 12-31-2023 I like a 1/4 - 6 hook toothed blade. I prefer Timberwolf blades for my 14 inch saw. It is the only blade I use on this saw. I have a 17 inch Grizzly band saw that I keep a 3/4 Wood Slicer blade from Highland Woodworking on. I like the blade. I do not do a lot of re-sawing, but I do do some. I tend to use it more for just ripping. I sharpen it with a die grinder. Like I said I do not do a lot of re-sawing but I have a friend that has a 1/2 wood slicer blade for his 1940s model, 14 inch Delta and he loves it. I have seen his results and I am not afraid to recommend it for a 14 inch saw. If John can get good results then any one can. A 1/2- 3 tooth blade is also a good choice for a resaw blade your saw, especially if you do not do a lot of it.. Again I tend to go with Timberwolf. I tried buying blades off from the shelf at a big box but theywere pure junk. I am sure that there are several good blade manufacturers out there, but I have never been disappointed with Timberwolf so I stay with them. Tom PS: If you are asking what you should be looking for then I wouldn't be worrying about blade thickness (0.02) I would be more concerned about number if teeth. RE: New Harbor Freight 14” Bandsaw in search of blades - Admiral - 12-31-2023 Tom's advice is spot on. +1 RE: New Harbor Freight 14” Bandsaw in search of blades - Stwood_ - 12-31-2023 I keep multi widths for my MM16. Most all are 3-4 TPI. The wider the blade, I spec less teeth. I've just got another order from these folks. I've bought from them close to 20 years. https://www.bandsawbladesdirect.com/ RE: New Harbor Freight 14” Bandsaw in search of blades - Johnny Currado - 01-01-2024 (12-31-2023, 11:56 AM)tablesawtom Wrote: I like a 1/4 - 6 hook toothed blade. I prefer Timberwolf blades for my 14 inch saw. It is the only blade I use on this saw. I have a 17 inch Grizzly band saw that I keep a 3/4 Wood Slicer blade from Highland Woodworking on. I like the blade. I do not do a lot of re-sawing, but I do do some. I tend to use it more for just ripping. I sharpen it with a die grinder. Like I said I do not do a lot of re-sawing but I have a friend that has a 1/2 wood slicer blade for his 1940s model, 14 inch Delta and he loves it. I have seen his results and I am not afraid to recommend it for a 14 inch saw. If John can get good results then any one can. RE: New Harbor Freight 14” Bandsaw in search of blades - Johnny Currado - 01-01-2024 (12-31-2023, 02:33 PM)Stwood_ Wrote: I keep multi widths for my MM16. Most all are 3-4 TPI. The wider the blade, I spec less teeth. Awesome thank you. RE: New Harbor Freight 14” Bandsaw in search of blades - Johnny Currado - 01-08-2024 (12-31-2023, 02:33 PM)Stwood_ Wrote: I keep multi widths for my MM16. Most all are 3-4 TPI. The wider the blade, I spec less teeth. What speed should I be setting my bandsaw at? ergo placement of the belts? I know I have a few options and I am not sure what is best or does it depend on wood thickness and type of wood too? RE: New Harbor Freight 14” Bandsaw in search of blades - kurt18947 - 01-09-2024 (01-08-2024, 07:36 PM)Johnny Currado Wrote: What speed should I be setting my bandsaw at? ergo placement of the belts? I know I have a few options and I am not sure what is best or does it depend on wood thickness and type of wood too? For wood I've always seen around 3000 feet/minute for small band saws. I guess if I were resawing and the motor was straining I'd select a lower speed and the attendant slower feed speed. Blades, lots of people are happy with Lenox and they're available from different sources. If you want something that may last longer consider bimetal blades. Diemaster II seems pretty popular even though that blade isn't intended primarily for cutting wood - it still works pretty well and it reputed to last about 5 times longer than common steel blades. RE: New Harbor Freight 14” Bandsaw in search of blades - Johnny Currado - 01-15-2024 (01-09-2024, 11:08 AM)kurt18947 Wrote: For wood I've always seen around 3000 feet/minute for small band saws. I guess if I were resawing and the motor was straining I'd select a lower speed and the attendant slower feed speed. Blades, lots of people are happy with Lenox and they're available from different sources. If you want something that may last longer consider bimetal blades. Diemaster II seems pretty popular even though that blade isn't intended primarily for cutting wood - it still works pretty well and it reputed to last about 5 times longer than common steel blades. awesome bud. Thanks for the information on the blades and speed too. Much appreciated. RE: New Harbor Freight 14” Bandsaw in search of blades - Cian - 01-15-2024 I used to have that HF bandsaw, and I won't hesitate to say that it did run smoother than the Delta bandsaw that replaced it. As far as blades go, I too use and been happy with Timberwolf blades. |