+- Woodnet Forums (https://forums.woodnet.net)
+-- Thread: Build a case? (/showthread.php?tid=7375445)
Build a case? - bandit571 - 03-23-2024
Time to get back to making things....besides making metal shiny? These need a case made..
[attachment=50389]
3/4" diameter Dies, and a Die Holder.
Had bought 4 of these planks at Lowes a while back..
[attachment=50390]
The 4th one was cut into 3 equal parts ( other 3 could be made into a case for the "New Chisels"?)
Parts were a bit cupped, so...
[attachment=50391]
This one is to be a lid for the case...the other 2? Well one needed to be worked on a different way...
[attachment=50392]
Traced around the Die holder, bolts and all...may have picked a too big of a blade, was hard to make some of the curves....
[attachment=50393]
Came time to glue these 2 together...Placed them so that the cups met like this..() then used the clamps to flatten them together into the spread out glue..
[attachment=50394]
Until I got a good squeeze out all around...will let this sit a day....then clean things up/out...and level and square it up..
I found an old bit for a Brace drill, that was a bit over-sized from a #12 bit..might be a#13? Intend to drill out a hole for each Die..5 above the holder, and 5 below.
The label each as to what size Die is in the holes.
Add a pair of hinges and a latch....and the Branding iron to the lid.
Stay tuned...
RE: Build a case? - bandit571 - 03-25-2024
Bottom 2/3rds is out of the clamps, needing jointed a bit..
[attachment=50396]
The plane?
[attachment=50397]
Stanley No. 5-1/2c, Type 11....then smoothed things down with..
[attachment=50398]
A Stanley No. 4-1/2c smoother, trying to get all parts to match up..
[attachment=50399]
Then do a wee bit of layout work...
[attachment=50400]
And do the same for the other 5 Dies..
Need a drill bit to drill holes to house the Dies,,,without going all the way through...and needed a bit a little bigger than the Dies..
[attachment=50401]
I think that No. 14/16ths should be about the right size?
[attachment=50402]
And, IF you count the full rotations after the bit starts to work..
[attachment=50403]
In this case, about 8 turns seems to work...and the snail did not poke through, either...
[attachment=50404]
Labeled according to size.
Brace drill? A Millers Falls "Buck Rogers" No. 1950..
Stay tuned...have to attach that lid....and maybe add a coat of stain?
RE: Build a case? - bandit571 - 03-25-2024
Need to roll this back up..
[attachment=50405]
Near as I can tell, these are all Irwins..
Clamped the lid to the case...and installed some hinges..
[attachment=50406]
Yep..these big hinges..
[attachment=50407]
Pencil for scale...I even clocked the screws....
While the edges were handy in the vise..
[attachment=50408]
Stanley No. 60-1/2 did round-overs..to all the sharp edges...ends and all..
Rotate things around, and installed a latch..
[attachment=50409]
AFTER the edges had been rounded over.
Next up, open a can of stain, the right way..
[attachment=50410]
Made in China, no less. Stained the outside, AFTER I labeled the lid...
[attachment=50411]
top edge of the latch, stuck up a bit....hammered it over to match the round-over..
Letting this dry a day...then a top coat of some sort...
Stay tuned..
RE: Build a case? - bandit571 - 03-27-2024
There is now a coat of Amber Shellac..inside and out...have a few errands to run, today....will rub things down this evening..and then decide on a Final coat...
Stay tuned..