Search Results
|
Post |
Author |
Forum |
Replies |
Views |
Posted
[asc]
|
|
|
Thread: delta 31-250 drum sander problem
Post: RE: delta 31-250 drum sander problem
Roly Wrote: (08-27-2021, 09:53 AM)
--
If part #69 is the gear you are referring to, it shows a set screw in it. Screw #8
If you are talking part #55 there is a roll pin that may be sheared off. i... |
|
flip |
Woodworking Power Tools
|
4 |
2,157 |
08-27-2021, 11:57 AM |
|
|
Thread: delta 31-250 drum sander problem
Post: RE: delta 31-250 drum sander problem
lkomroff Wrote: (08-26-2021, 06:03 PM)
--
It looks like a 5/16x18 set screw is used. See part #48 here:
https://www.ereplacementparts.com/delta-31250-type-drum-sander-parts-c-3275_3512_3539.html (ht... |
|
flip |
Woodworking Power Tools
|
4 |
2,157 |
08-27-2021, 08:40 AM |
|
|
Thread: delta 31-250 drum sander problem
Post: delta 31-250 drum sander problem
I have had this drum sander a long time and used it a lot. Today, the crank that raises and lowers the feed table broke free from drive gear that moves the table. I have looked at the connection and... |
|
flip |
Woodworking Power Tools
|
4 |
2,157 |
08-26-2021, 05:33 PM |
|
|
Thread: Miniwax Polycrylic
Post: RE: Miniwax Polycrylic
Rob Young Wrote: (11-10-2019, 08:50 AM)
--
General Finishes Extender will increase the open time and make the water based finish flow better under most application conditions.
They are sold by any... |
|
flip |
Finishing
|
38 |
26,822 |
11-10-2019, 04:22 PM |
|
|
Thread: Miniwax Polycrylic
Post: RE: Miniwax Polycrylic
jteneyck Wrote: (11-09-2019, 08:24 PM)
--
Have you tried a foam brush? If so, and you are still getting brush marks, then get some of GF's Extender and add about 4% and see if that helps.
Joh... |
|
flip |
Finishing
|
38 |
26,822 |
11-10-2019, 05:52 AM |
|
|
Thread: Miniwax Polycrylic
Post: RE: Miniwax Polycrylic
jteneyck Wrote: (06-29-2018, 09:34 AM)
--
Why yes it would, and what I do most of the time.
FWIW, I find Polycrylic soft and easily scratched, as noted above. It does spray nicely, but so do m... |
|
flip |
Finishing
|
38 |
26,822 |
11-09-2019, 06:23 PM |
|
|
Thread: finish for outdoor mahogany deck
Post: RE: finish for outdoor mahogany deck
Have ordered same. Thank you so much for your help. |
|
flip |
Finishing
|
8 |
6,818 |
05-08-2018, 02:33 PM |
|
|
Thread: finish for outdoor mahogany deck
Post: RE: finish for outdoor mahogany deck
Which Penefin oil, several kinds available on Penefin website. How many coats? When you say "clean and renew". what does that entail? Thanks. |
|
flip |
Finishing
|
8 |
6,818 |
05-08-2018, 09:15 AM |
|
|
Thread: finish for outdoor mahogany deck
Post: RE: finish for outdoor mahogany deck
You have any opinion on a clear epoxy finish? Like that used for garage floor without any flakes for color? |
|
flip |
Finishing
|
8 |
6,818 |
05-04-2018, 05:18 AM |
|
|
Thread: finish for outdoor mahogany deck
Post: RE: finish for outdoor mahogany deck
Not sure or original finish but I applied a deck sealer about five years ago. My intent is to completely remove old finish to get to raw wood. |
|
flip |
Finishing
|
8 |
6,818 |
05-03-2018, 03:51 PM |
|
|
Thread: finish for outdoor mahogany deck
Post: finish for outdoor mahogany deck
Am going to sand and refinish my Mahogany deck and would like some advice on what finish to use. Am told that Spar Varnish is not hard enough for floor traffic. Req'ts are hardness and durability al... |
|
flip |
Finishing
|
8 |
6,818 |
05-03-2018, 06:54 AM |
|
|
Thread: Dewalt 625 template subbase
Post: Dewalt 625 template subbase
Apparently I have lost the guide bushing plate that came with the Dewalt 625 Plunge router. It is a plate that attaches to the router base. I don't see it in the schematic of replacement parts(erepl... |
|
flip |
Woodworking Power Tools
|
2 |
2,791 |
12-10-2016, 09:28 AM |
|
|
Thread: stuck router bit
Post: RE: stuck router bit
Put bit in my vise (wooden jaws) and tapped the collet. Came loose immediately. Thanks to all. |
|
flip |
Woodworking Power Tools
|
10 |
8,428 |
11-21-2016, 10:27 AM |
|
|
Thread: stuck router bit
Post: stuck router bit
I have a seized up bit in my PC laminate trimmer. Any suggestions on how to get it out? Should have anticipated this when it was difficult to get it into the collet. Bit is 1/4" shank 1/8" carbide. |
|
flip |
Woodworking Power Tools
|
10 |
8,428 |
11-21-2016, 07:38 AM |