Search Results
|
Post |
Author |
Forum |
Replies |
Views |
Posted
[asc]
|
|
|
Thread: Where to buy Faux marble trim
Post: Where to buy Faux marble trim
Will be rebuilding the shower and want to go back with a frameless shower enclosure and will need to replace this trim piece between the shower and tub.
Where can I buy this? |
|
thinshavings |
Home Improvement
|
2 |
223 |
02-01-2024, 08:52 AM |
|
|
Thread: Go Board
Post: RE: Go Board
KC Wrote: (01-21-2024, 07:35 AM)
--
Doesn't look anything like Ditra on the Lowe's site.
At $10 more per sheet than DUROCK (and HardiBacker priced in between), I don't see any benefit other than... |
|
thinshavings |
Home Improvement
|
5 |
626 |
01-21-2024, 02:27 PM |
|
|
Thread: Go Board
Post: Go Board
Anyone with experience using Go Board as waterproof backer for ceramic tile in a shower? |
|
thinshavings |
Home Improvement
|
5 |
626 |
01-20-2024, 11:21 AM |
|
|
Thread: Woodworker's Supply Inc. has Closed it's doors after 51 years
Post: Woodworker's Supply Inc. has Closed it's doors aft...
https://woodworker.com/WSI_logo.jpg (https://woodworker.com/)
Woodworker's Supply Inc. has Closed it's doors after 51 years of serving the woodworking community.
This decision was not reached li... |
|
thinshavings |
Woodworking
|
18 |
2,602 |
12-17-2023, 08:45 PM |
|
|
Thread: spray foam insulation - dangers and downfalls
Post: RE: spray foam insulation - dangers and downfalls
Not recommended here on the gulf coast at all. |
|
thinshavings |
Home Improvement
|
30 |
8,266 |
06-15-2023, 08:36 PM |
|
|
Thread: Help with hand planes
Post: RE: Help with hand planes
After decades of old Stanley planes I purchased a LN 5 1/2 jack and a low angle block plane last December. All I can say is should have bought them decades ago. The LN planes are like a fine Swiss wat... |
|
thinshavings |
Woodworking Hand Tools
|
38 |
4,612 |
03-17-2023, 08:42 PM |
|
|
Thread: Free Delta Contractor Table Saw (minus motor) (redwood city)
Post: RE: Free Delta Contractor Table Saw (minus motor) ...
Wow....free!
I have one that is my shop saw bought used in about 1988.
With that exact fence works well for me have never seen a need to "ugrade". |
|
thinshavings |
Tool Swap N' Sell
|
2 |
654 |
12-19-2022, 07:33 PM |
|
|
Thread: WTB WS3000 Tool Bar Attachment
Post: WTB WS3000 Tool Bar Attachment
The one that can use Tormek turning tool jigs. |
|
thinshavings |
Tool Swap N' Sell
|
0 |
417 |
12-15-2022, 08:49 PM |
|
|
Thread: Milwaukee finish nailer
Post: RE: Milwaukee finish nailer
EdL Wrote: (03-20-2022, 04:02 PM)
--
Did you try e-replacment parts?
Ed
--
Yup...says "this part has been discontinued or is no longer available."
:mad: |
|
thinshavings |
Woodworking Power Tools
|
4 |
1,460 |
03-20-2022, 05:00 PM |
|
|
Thread: Milwaukee finish nailer
Post: Milwaukee finish nailer
Any one know of a source for a seal part # 45-06-0950 ?
This is for a Milwaukee model 7140-21 angled finish nailer. |
|
thinshavings |
Woodworking Power Tools
|
4 |
1,460 |
03-20-2022, 11:51 AM |
|
|
Thread: Bathroom Remodel
Post: RE: Bathroom Remodel
Jack01 Wrote: (06-07-2020, 11:43 AM)
--
Thanks for the suggestions, I did check that , it looks good, unfortunately it will not fit in the shower enclosure I Have. It has 3 walls, one of the side of ... |
|
thinshavings |
Home Improvement
|
13 |
6,162 |
11-28-2020, 03:44 PM |
|
|
Thread: Walnut secretary desk completed
Post: RE: Walnut secretary desk completed
|
thinshavings |
Woodworking
|
48 |
16,944 |
01-31-2020, 08:28 PM |
|
|
Thread: Neglected by table saw (rust)
Post: RE: Neglected by table saw (rust)
cputnam Wrote: (03-19-2019, 06:01 PM)
--
Wax is not a rust protectant. Use something designed specifically as a metal rust protector. CorrosionX, Boeshield, or true synthetic motor oil. Let it sit... |
|
thinshavings |
Woodworking Power Tools
|
14 |
7,156 |
04-14-2019, 06:15 PM |
|
|
Thread: Cost of HVAC replacement
Post: Cost of HVAC replacement
Looking at replacing our homes HVAC system.
5 ton A/C , gas furnace, two story home with 2 -14 inch zone dampners.
How much do you think this will cost using a 14 SEER unit? |
|
thinshavings |
Home Improvement
|
21 |
14,730 |
03-22-2017, 08:06 PM |
|
|
Thread: Copper coils or aluminum?
Post: RE: Copper coils or aluminum?
Robert Adams Wrote: (12-11-2016, 07:08 PM)
--
Pretty much all are aluminum evaporated coils. Personally I prefer copper but the copper used in coils has gotten much thinner to improve efficiency howe... |
|
thinshavings |
Home Improvement
|
8 |
4,900 |
12-11-2016, 09:47 PM |
|
|
Thread: Copper coils or aluminum?
Post: Copper coils or aluminum?
Will soon be seeking bids on a new A/C system.
I haven't purchased one in many years so what is the opinion on coil material? |
|
thinshavings |
Home Improvement
|
8 |
4,900 |
12-11-2016, 06:28 PM |
|
|
Thread: Shaker Candle Stand Plans
Post: Re: Shaker Candle Stand Plans
Nice job!![br]I made one ( from Norm's plans) back in the '90's. |
|
thinshavings |
Woodworking
|
6 |
9,447 |
12-28-2014, 08:36 PM |