Search Results
|
Post |
Author |
Forum |
Replies |
Views |
Posted
[asc]
|
|
|
Thread: Gluing onto Polyurethane Finished Wood?
Post: RE: Gluing onto Polyurethane Finished Wood?
fredhargis Wrote: (06-09-2021, 02:39 PM)
--
Maybe clear some of the varnish off where the letters go and use PVA to glue the letters to the wood itself?
Removing the finish under the letters may b... |
|
tbr |
Woodworking
|
12 |
7,563 |
06-09-2021, 03:02 PM |
|
|
Thread: Gluing onto Polyurethane Finished Wood?
Post: RE: Gluing onto Polyurethane Finished Wood?
MT WoodworkerInstead of glue, possibly just use a pin nailer?
The letters are very small so a pin nail would be too large. But thanks for the suggestion. |
|
tbr |
Woodworking
|
12 |
7,563 |
06-09-2021, 02:58 PM |
|
|
Thread: Gluing onto Polyurethane Finished Wood?
Post: Gluing onto Polyurethane Finished Wood?
I would like to glue small wooden letters to wood that has a polyurethane finish. What would be the best glue for this? Would Titebond work or is there something that will hold better? |
|
tbr |
Woodworking
|
12 |
7,563 |
06-09-2021, 02:27 PM |
|
|
Thread: Plunge Router with Good Depth Control
Post: Plunge Router with Good Depth Control
I currently have a Porter Cable router with a plunge base. Over the years of use, the locking screw that holds the sliding depth rod no longer securely locks the rod place. I have replaced the locking... |
|
tbr |
Woodworking Power Tools
|
2 |
1,097 |
10-22-2020, 06:54 PM |
|
|
Thread: Calibrating Miter Gauge Woes?
Post: RE: Calibrating Miter Gauge Woes?
You should check to make sure your blade is parallel to the miter slot using a dial indicator (I use an A-Line-It made by Incra). You then can build a sled with a fixed 45 degree fence using a draftin... |
|
tbr |
Woodworking Power Tools
|
35 |
20,602 |
11-10-2017, 07:21 PM |
|
|
Thread: Looking for bandsaw resawing blade suggestions
Post: RE: Looking for bandsaw resawing blade suggestions
Thank you everyone for your suggestions and advice. I would like to get a carbide tipped blade but current budget considerations have place the them out of reach for the moment. As such, I purchased a... |
|
tbr |
Woodworking Power Tools
|
26 |
24,859 |
10-27-2017, 07:12 PM |
|
|
Thread: Looking for bandsaw resawing blade suggestions
Post: RE: Looking for bandsaw resawing blade suggestions
Jason,
Thanks for the detailed reply. Although I originally mentioned that I was looking for a 3/4” blade, if that is not necessarily suitable for the 325, would a 1/2” blade handle the type of res... |
|
tbr |
Woodworking Power Tools
|
26 |
24,859 |
10-21-2017, 09:21 PM |
|
|
Thread: Looking for bandsaw resawing blade suggestions
Post: Looking for bandsaw resawing blade suggestions
I have a Rikon 10-325 bandsaw (111” blades) and am planning to buy a 3/4” blade for resawing hardwood up to 4” thick to make 1/8” thick pieces for inlay. I am looking for suggestions for a good qualit... |
|
tbr |
Woodworking Power Tools
|
26 |
24,859 |
10-21-2017, 07:39 PM |
|
|
Thread: Miter Saws ideas
Post: RE: Miter Saws ideas
Yes I am talking about the zero clearance fence. I used a piece of MDF and screwed into a extra table saw insert. As for the stop, it works well and I have used for table saw cuts other than segments... |
|
tbr |
Woodturning
|
9 |
5,146 |
08-09-2017, 11:00 AM |
|
|
Thread: Miter Saws ideas
Post: RE: Miter Saws ideas
I started out making segments using a miter saw, but quickly found my table saw to be much more accurate and reproducible. I built a Wedgie Sled as described on this web site as well as You Tube vid... |
|
tbr |
Woodturning
|
9 |
5,146 |
08-08-2017, 07:41 PM |