Search Results
|
Post |
Author |
Forum |
Replies |
Views |
Posted
[asc]
|
|
|
Thread: Ever make hardwood flooring?
Post: RE: Ever make hardwood flooring?
Tapper Wrote: (02-07-2019, 12:03 PM)
--
Just for clarification, does "no end match" mean no T&G on the ends?
Doug
Who installed and finished ~2,500 sq. ft. of 3 1/4" rift and QS white oak in hi... |
|
Phancy |
Woodworking
|
23 |
9,799 |
02-08-2019, 01:16 PM |
|
|
Thread: Self closing drawer slides
Post: RE: Self closing drawer slides
jteneyck Wrote: (01-28-2019, 12:59 PM)
--
KV 8455FM Soft-Close Full Extension with Overtravel Drawer Slides (https://www.wwhardware.com/kv-8455-soft-close-full-extension-with-overtravel-drawer-slide... |
|
Phancy |
Woodworking
|
10 |
6,516 |
02-02-2019, 07:04 AM |
|
|
Thread: Ever make hardwood flooring?
Post: RE: Ever make hardwood flooring?
Yes I have made my flooring, mostly. I cleared a building site (4 years ago) for our new house, heavily wooded with mature red oak. I cut the trees down, cut logs 8 to 10 feet long, drug them to a ne... |
|
Phancy |
Woodworking
|
23 |
9,799 |
02-02-2019, 06:57 AM |
|
|
Thread: Stupid question about Saw Blades
Post: RE: Stupid question about Saw Blades
I once sent a blade to a low end sharpening shop that needed a few new carbides replaced. When I got the blade back it looked like they glued them on with bubble gum. I do not remember how that blade ... |
|
Phancy |
Woodworking
|
21 |
10,192 |
03-06-2018, 06:41 AM |
|
|
Thread: Jointer tune up
Post: RE: Jointer tune up
thooks Wrote: (12-28-2017, 11:08 AM)
--
How did you know you had a problem previously? Was it showing up in long board glue-ups?
If so, then make some MINOR adjustments to fix the problem. Then ... |
|
Phancy |
Woodworking Power Tools
|
17 |
9,140 |
12-28-2017, 11:55 AM |
|
|
Thread: Jointer tune up
Post: RE: Jointer tune up
Strokes77 Wrote: (12-27-2017, 08:40 PM)
--
I would phrase it this way, hopefully not too harsh... You've worked for 15 years without a problem. But now you have a fancy 8' strait edge, and you are ... |
|
Phancy |
Woodworking Power Tools
|
17 |
9,140 |
12-28-2017, 05:08 AM |
|
|
Thread: Jointer tune up
Post: RE: Jointer tune up
Phil Thien Wrote: (12-27-2017, 05:52 PM)
--
So you used a 5' or 6' long straight edge, clamped to the outfeed table and extending to the end of your infeed table, and have determined that the end of ... |
|
Phancy |
Woodworking Power Tools
|
17 |
9,140 |
12-27-2017, 06:18 PM |
|
|
Thread: Jointer tune up
Post: RE: Jointer tune up
woodhead Wrote: (12-27-2017, 04:27 PM)
--
so what's that, like a 64th of an inch?
0.015625
Al
--
Yes a 64th of an inch which may cause a convex curve in the center of a long board. That is m... |
|
Phancy |
Woodworking Power Tools
|
17 |
9,140 |
12-27-2017, 05:23 PM |
|
|
Thread: Jointer tune up
Post: Jointer tune up
I have an 8" Jet jointer that I bought new about 17 years ago. I am an avid intermediate woodworker that wants to advance my quality of work and make things easier. Not knowing the tolerances of my jo... |
|
Phancy |
Woodworking Power Tools
|
17 |
9,140 |
12-27-2017, 02:17 PM |