Search Results
|
Post |
Author |
Forum |
Replies |
Views |
Posted
[asc]
|
|
|
Thread: Putting paint over varnish - outside
Post: Putting paint over varnish - outside
About three years ago I visited this forum asking for advice/counsel for a project that I was working on. The project was making a set of church doors for an old church that was being restored. The ... |
|
Retiredguy |
Finishing
|
7 |
1,533 |
10-30-2022, 09:01 PM |
|
|
Thread: Valhalla Lifetime Wood Treatment
Post: Valhalla Lifetime Wood Treatment
All:
Has anyone used or have knowledge about Valhalla Lifetime Wood Treatment?
It sounds waaaay too good to be true, especially since it is water based,
Ross |
|
Retiredguy |
Finishing
|
2 |
1,951 |
02-01-2019, 09:57 AM |
|
|
Thread: Mortise & Tenion Expansion/Contraction
Post: RE: Mortise & Tenion Expansion/Contraction
jteneyck Wrote: (08-05-2018, 06:47 PM)
--
That sounds like a reasonable approach. Have you tried cutting ccw? It's not something I normally do but if the depth of cut is only 1/8" it should be ok a... |
|
Retiredguy |
Woodworking
|
17 |
9,781 |
08-05-2018, 07:59 PM |
|
|
Thread: Mortise & Tenion Expansion/Contraction
Post: RE: Mortise & Tenion Expansion/Contraction
jteneyck Wrote: (08-04-2018, 05:47 PM)
--
I've never used a 4 flute end mill, but I would guess it would cut slowly but smoothly. If that's true, I wonder if you are trying to take too deep a cut. ... |
|
Retiredguy |
Woodworking
|
17 |
9,781 |
08-05-2018, 05:33 PM |
|
|
Thread: Mortise & Tenion Expansion/Contraction
Post: RE: Mortise & Tenion Expansion/Contraction
jteneyck Wrote: (07-28-2018, 02:49 PM)
--
You can buy end mills that will allow you to go about as deep as you want for the mortises. I use center drilling, 2 or 3 fluted HSS end mills. You can buy... |
|
Retiredguy |
Woodworking
|
17 |
9,781 |
08-04-2018, 05:22 PM |
|
|
Thread: Mortise & Tenion Expansion/Contraction
Post: RE: Mortise & Tenion Expansion/Contraction
rwe2156 Wrote: (07-28-2018, 08:54 AM)
--
Yes, I would definitely make the tenon longer, at least 3 1/2".
IMO the best approach is glue & pin the tenon closest to edge so the edge stays flush with... |
|
Retiredguy |
Woodworking
|
17 |
9,781 |
07-28-2018, 01:36 PM |
|
|
Thread: Mortise & Tenion Expansion/Contraction
Post: RE: Mortise & Tenion Expansion/Contraction
fredhargis Wrote: (07-27-2018, 01:13 PM)
--
I would glue them all, there are no concerns with expansion on 2" tenons. Curious, how thick are those tenons?
--
Thank you for your input, that's what I... |
|
Retiredguy |
Woodworking
|
17 |
9,781 |
07-27-2018, 07:39 PM |
|
|
Thread: Mortise & Tenion Expansion/Contraction
Post: Mortise & Tenion Expansion/Contraction
I am building two Church doors to replace the 156 YO originals.
The doors are Red Oak 1 3/4" thick, and each door is 30 X 96 inches, with two 5" wide styles, and four rails (3 3/4", 6", 7" and 11").
... |
|
Retiredguy |
Woodworking
|
17 |
9,781 |
07-27-2018, 12:17 PM |
|
|
Thread: Who are you
Post: Re: Who are you
Hello, my name is Ross. [br]I have had a lathe for several years, made stuff, even sold some, but never felt that I really understood what I was doing with the lathe. [br]I retired from my day job i... |
|
Retiredguy |
Woodturning
|
457 |
148,500 |
03-02-2008, 04:38 PM |