Search Results
Post Author Forum Replies Views Posted [asc]
  0 Thread: Looking to source some hinges
Post: RE: Looking to source some hinges

Another source would be Lee Valley.
lift mechanic Woodworking 5 251 06-13-2022, 12:29 PM
  0 Thread: One incredible beast od a RAS
Post: RE: One incredible beast od a RAS

I have one similar to this RAS. it is a Comet radial arm saw 16" blade 5 hp built onto a trailer. It was built back in the 1950's.  I used it to build the house I'm living in, have not used it for 6 y...
lift mechanic Woodworking Power Tools 3 283 06-11-2022, 12:38 PM
  0 Thread: Cracked and sinking concrete floor
Post: RE: Cracked and sinking concrete floor

I am with Snipe Hunter, Remove,  compact and repour. If were in my shop I would cut it so it would be a straight edge and probably square it off.
lift mechanic Home Improvement 14 836 05-05-2022, 02:13 PM
  0 Thread: Alternative to pressure treated
Post: RE: Alternative to pressure treated

I just saw some neat brackets used on steel "T" posts to brace the corners. I saw them on YouTube on "Wild Wonderful Off-Grid" there latest vid titled "were halfway there" starting at 1:45 mins.  I ha...
lift mechanic Home Improvement 11 628 04-15-2022, 11:04 AM
  0 Thread: Miter Sled - Features Important to You?
Post: RE: Miter Sled - Features Important to You?

Long runners, replaceable zero clear insert for 90 and 45. A 45 deg bolt in fence for like doing picture frames. Runners that are adjustable to fit the miter slot.
lift mechanic Woodworking 26 1,926 04-06-2022, 11:27 PM
  0 Thread: Stand On Rubber Mat
Post: RE: Stand On Rubber Mat

Do you find the rubber mats a pain to sweep around? I mainly have wood saw dust but sometimes steel drill shavings at the drill press. I know the steel from the drill press gets stuck in the broom whe...
lift mechanic Home Improvement 18 1,269 03-26-2022, 10:35 AM
  0 Thread: How to deal with this tear out?
Post: RE: How to deal with this tear out?

I just had the same type of tear out but on an alder panel. I decided to repair it even though it will not show. I used clear "Stick Fast" CA glue and an accelerator. Never used it before. I just spre...
lift mechanic Woodworking 16 1,313 03-20-2022, 10:39 PM
  0 Thread: questions on slab for shed
Post: RE: questions on slab for shed

Around my chicken coop I buried chicken wire about 12" deep to keep the varmints out. It has been 6 years now and nothing has dug under the coop. I had a small slab poured last year, 12' x 14'. The co...
lift mechanic Home Improvement 10 825 03-19-2022, 12:10 PM
  0 Thread: Punch Saw For Plaster Wall?
Post: RE: Punch Saw For Plaster Wall?

Drill a 1/2" hole and use a jig saw to make the cut.
lift mechanic Home Improvement 7 646 03-14-2022, 09:57 PM
  0 Thread: Festool Sanders Dust Collection
Post: RE: Festool Sanders Dust Collection

About a month ago I made the leap to the Festool CT 15 hepa vacume and the ETS 125/3 EQ-Plus sander. The dust collection is much better than my other sander that I could hook up to a shop vac. The onl...
lift mechanic Woodworking Power Tools 13 893 03-13-2022, 12:44 AM
  0 Thread: Finishing Stair Treads
Post: RE: Finishing Stair Treads

The Bona "Traffic" works quite well. I have a fairly soft flooring, circular sawn Duglas fir. I lightly sanded the flooring, stained with oil base. Then 2 coats of Bona "Mega" the 2 coats of Bona "Tra...
lift mechanic Home Improvement 15 831 03-12-2022, 01:09 AM
  0 Thread: Bringing tools out of long term storage
Post: RE: Bringing tools out of long term storage

Sounds like you did what you could do before storage. I am no expert but working on machinery for 42 years, the electrical on the machines and tools are not normally a problem. Grease what you can. Tu...
lift mechanic Woodworking Power Tools 5 500 03-09-2022, 11:22 PM
  0 Thread: DeWalt 18v to 20v Adapter?
Post: RE: DeWalt 18v to 20v Adapter?

Thank for the information. Guess I will get the adapter, charger and a couple of batteries. Good to know about leaving the batteries in the adapter. I think the 20v DeWalt will be around for a while.
lift mechanic Woodworking Power Tools 4 444 03-08-2022, 12:44 AM
  0 Thread: DeWalt 18v to 20v Adapter?
Post: DeWalt 18v to 20v Adapter?

I have several 18v DeWalt tools. My second battery just stopped charging, now down to 3 batteries. Anyone have experience with the adapter? Does the 20v batteries last as long as the lithiumion 18v XR...
lift mechanic Woodworking Power Tools 4 444 03-04-2022, 04:28 PM
  0 Thread: Interior door finishing stands?
Post: RE: Interior door finishing stands?

I am applying the final coat of Arm R-Seal to the last 2 doors. I ended up cutting some plywood into 7" triangles. Drilled a 1/4" hole near the top of the triangle. Pre drilled the door stiles for 4" ...
lift mechanic Finishing 10 1,561 03-01-2022, 03:44 PM
  0 Thread: Power Twist Link Belts
Post: RE: Power Twist Link Belts

Ski lifts use a lot of belts to run the engine room machinery. We had some Power Twist belts for emergencies. Luckly never had to use them. The supplier of the belts always told us never to use them n...
lift mechanic Woodworking Power Tools 4 422 02-28-2022, 12:08 PM
  0 Thread: What to pour oil poly into for wiping?
Post: RE: What to pour oil poly into for wiping?

I like those 4" roller trays for wipe on poly. I use a foam brush to apply and a folded rag to wipe off. I use the the roller ramp to dab my brush after dipping  as I apply. I have 3 trays that I have...
lift mechanic Finishing 7 524 02-26-2022, 11:58 PM
  0 Thread: carbide inserts, why I don't change
Post: RE: carbide inserts, why I don't change

I have the spiral cutter head on both my jointer and planer. When I notice jointer getting a little harder to push the material over the bed I give it a spray of lube. Makes all the difference in the ...
lift mechanic Woodworking Power Tools 8 830 02-23-2022, 01:47 PM
  0 Thread: How To secure dust catcher liner?
Post: RE: How To secure dust catcher liner?

I haven't tried the cloths pin idea. The plastic sheeting slides out of the barrel, trash can liner very easy. I slide the " plastic holder" out of the trash can liner before removing the full trash c...
lift mechanic Woodworking 30 2,514 02-23-2022, 01:27 PM
  0 Thread: How To secure dust catcher liner?
Post: RE: How To secure dust catcher liner?

An up date. The 1/4" foam did not work. The foam was not stiff enough. I found a 1/16" stiff plastic sheet 48 x 96 for $16 @ HD. I cut it down to size and used Gorilla Tape on all the edges and taped ...
lift mechanic Woodworking 30 2,514 02-23-2022, 01:46 AM

Product Recommendations

Here are some supplies and tools we find essential in our everyday work around the shop. We may receive a commission from sales referred by our links; however, we have carefully selected these products for their usefulness and quality.