Search Results
Post Author Forum Replies Views Posted [asc]
  0 Thread: Daily Bench Shot
Post: RE: Daily Bench Shot

Gary G™ Wrote: (11-13-2022, 11:13 AM) -- Got enough squeeze out? -- Looks good...
Stwood_ Woodworking 1,665 538,887 11-13-2022, 06:28 PM
  0 Thread: Daily Bench Shot
Post: RE: Daily Bench Shot

Lookin good ya'll.
Stwood_ Woodworking 1,665 538,887 10-10-2022, 03:15 PM
  0 Thread: Daily Bench Shot
Post: RE: Daily Bench Shot

Bump.....................
Stwood_ Woodworking 1,665 538,887 08-05-2022, 01:46 PM
  0 Thread: Western red cedar
Post: RE: Western red cedar

Alan S Wrote: (08-02-2022, 03:39 PM) -- That looks more like eastern red cedar, (aromatic cedar) than western. -- Correct.
Stwood_ Woodworking 16 1,111 08-05-2022, 01:38 PM
  0 Thread: Daily Bench Shot
Post: RE: Daily Bench Shot

Rob Young Wrote: (07-17-2022, 09:30 PM) -- Did a little bit of work this weekend on a quick and dirty stand to hold two solar panels at 39* (my latitude) for testing. 3/4" plywood and a bit of iron p...
Stwood_ Woodworking 1,665 538,887 08-02-2022, 11:11 PM
  0 Thread: Who are you
Post: RE: Who are you

AnthonyYak Wrote: (07-17-2022, 07:16 PM) -- Oldest thread???????????????? -- Very possible. Ask cranky fred to research it.
Stwood_ Woodturning 457 132,517 08-02-2022, 10:38 PM
  0 Thread: Another old planer coming back to life!
Post: RE: Another old planer coming back to life!

So there is no kickback fingers/setup on this machine?
Stwood_ Woodworking Power Tools 19 2,350 07-05-2022, 01:16 PM
  0 Thread: Lacquer or Poly
Post: RE: Lacquer or Poly

I've gone to using water based poly on about everything. It lays out good when spraying and dries in 30 minutes so you can recoat fairly fast. Takes water spills really well. Can be brushed if you ha...
Stwood_ Woodworking 10 1,176 07-04-2022, 02:49 PM
  0 Thread: Parts and pieces
Post: RE: Parts and pieces

Looks like a pile back when I did cabinets. Side panels and doors. Pile up 4-500 rails and stiles and hope you didn't have to many oopsies in there.....
Stwood_ Woodworking 5 570 07-04-2022, 02:46 PM
  0 Thread: Raised panel door
Post: RE: Raised panel door

Just depends on the board. If it's 10" and sits there and cups a bit, better to rip and flip. Otherwise, use it as is. I never liked the mismatch's in the panels when having multiple boards glued up...
Stwood_ Woodworking 30 1,996 07-02-2022, 05:23 PM
  0 Thread: Raised panel door
Post: RE: Raised panel door

I always made my panels 5/8 when using 3/4 frames.
Stwood_ Woodworking 30 1,996 07-02-2022, 05:07 PM
  0 Thread: Air dried vs kiln dried
Post: RE: Air dried vs kiln dried

I've always used kiln dried. When in business, I did not need something shrinking up, especially door panels.
Stwood_ Woodworking 32 2,222 07-02-2022, 04:59 PM
  0 Thread: Daily Bench Shot
Post: RE: Daily Bench Shot

Lookin good.............
Stwood_ Woodworking 1,665 538,887 06-29-2022, 02:56 PM
  0 Thread: Spray top first or last
Post: RE: Spray top first or last

Like a table or desk, sides then top.
Stwood_ Finishing 3 390 05-30-2022, 06:12 PM
  0 Thread: Well Pressure Switch
Post: RE: Well Pressure Switch

The adjustment changes the pump pressure setting. Lowering it will be low pressure in the house. Raising it you could cause a leak in the house. They come set at 20-40 is the common one, and the ot...
Stwood_ Home Improvement 11 864 05-28-2022, 10:54 PM
  0 Thread: Accidentally Cut Underground Wire
Post: RE: Accidentally Cut Underground Wire

Electric grease on the connection before shrink tubing will keep the corrosion away.
Stwood_ Home Improvement 8 802 05-28-2022, 07:31 PM
  0 Thread: Well Pressure Switch
Post: RE: Well Pressure Switch

$25.00 switch, I'd replace it. I'd say it's defective and adjusting won't cure it. Those switches can last a lifetime. Good ones are usually Square D.
Stwood_ Home Improvement 11 864 05-28-2022, 07:28 PM
  0 Thread: Another old planer coming back to life!
Post: RE: Another old planer coming back to life!

Is the shaft with the safety fingers (for kickback) still in the machine? The shaft would wear and get pretty sloppy in there and some would remove those. It is a good idea to have those in working...
Stwood_ Woodworking Power Tools 19 2,350 05-28-2022, 07:05 PM
  0 Thread: trying to repair my Accuset 23g pin nailer
Post: RE: trying to repair my Accuset 23g pin nailer

Is the driver retracting back into the head, or just hanging out? Oil the driver shaft up, may be dry, or broken. Ereplacement may have o-ring kits yet if needed.
Stwood_ Woodworking Power Tools 3 519 05-28-2022, 06:56 PM
  0 Thread: Remove staples from wood
Post: RE: Remove staples from wood

If the staple is embedded, more than likely it won't pull out magically.
Stwood_ Woodworking 14 1,415 05-28-2022, 06:50 PM

Product Recommendations

Here are some supplies and tools we find essential in our everyday work around the shop. We may receive a commission from sales referred by our links; however, we have carefully selected these products for their usefulness and quality.